TP-Link td-w8961nd specs

•IGMP Snoop: Enable the IGMP Snoop function if you need.

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

•Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports both IGMP version 1 (IGMP v1) and IGMP v2. Select “Disabled” to disable it.

•IGMP Snoop: Enable the IGMP Snoop function if you need.

¾DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-12). The Router will work as a DHCP Server; it becomes the default gateway for DHCP client connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network.

Figure 4-12

•Starting IP Address: Enter the starting IP address for the DHCP server's IP assignment. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254.

•IP Pool Count: The max user pool size.

•Lease Time: The length of time for the IP lease. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 seconds.

¾DHCP Table: The information of the DHCP clients will be displayed here

26

Image 33

TP-Link td-w8961nd manual TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Contents

Rev 2.0.0 TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure Statement National Restrictions CE Mark WarningCountry Restriction Product Description 300Mbps Wireless N ADSL2+ Modem Router DECLARATION OF CONFORMITYShenzhen, P. R. China ETSI EN 300 328 V1.7.1 Hardware Installation Package ContentsQuick Installation Guide Software Configuration Appendix B Troubleshooting Appendix A SpecificationsAppendix C Technical Support Maintenance Package Contents 300Mbps Wireless N ADSL2+ Modem Router User GuideTD-W8961ND Wireless 1.2 Main FeaturesChapter 1 Introduction 1.1 Product Overview TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 Conventions 2.1 The Front Panel Chapter 2 Hardware InstallationLED Explanation Name 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.3 Installation Environment 2.4 Connecting the RouterBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3 Quick Installation Guide TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 3.2 Login 2 Is the TCP/IP configuration for your PC correct?1 Is the connection between your PC and the Router correct? and Connection Type. Then click NEXT Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 6 Click NEXT to finish the Quick Start Step 5 Configure the rules for the WLAN, and click NEXT Chapter 4 Software Configuration 4.1 Status4.1.1 Device Info 4.1.2 System Log 4.1.3 Statistics Click the CLEAR LOG button to clear the logsClick the SAVE LOG button to save the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below Please refer to 3.2 Login 4.2 Quick Start¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below 4.3.1 Internet 4.3 Interface Setup 1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4 Bridge Mode 4.3.2 LAN TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect How to assign a static IP address to the client? 4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 3 WPA-PSK 2 WEP-128Bits 5 WPA-PSK/WPA2-PSK 4 WPA2-PSK 4.3.3.1 WPS Settings 1 PBCMethod One Method Two 2 PIN code TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND 4.4.1 Firewall 4.4 Advanced Setup 4.4.2 Routing 4.4.3 NAT 4.4.3.2 Virtual Server 4.4.3.1 DMZ To add a virtual server entry Other operations for the entries as shown in Figure4.4.3.3 IP Address Mapping 4.4.4 QoS To add a mapping ruleIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 2 Define VLAN Group 1 Assign VLAN PVID for each Interface 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management 4.5.2.1 IP Filter 4.5.2 Filter ¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.2 MAC Filter 4.5.2.3 Application Filter Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL Filter To add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP 4.5.6 CWMP 4.5.5 DDNS 4.6 Maintenance 4.6.1 Administration 4.6.2 Time Zone1 NTP Server automatically 3 Manually 2 PC’s Clock To upgrade the routers firmware, follow these instructions below 4.6.3 Firmware 3 The router will reboot after the upgrading has been finished To back up the Router’s current settingsTo restore the Router’s settings 4.6.4 SysRestart 4.6.5 Diagnostics 4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Appendix A Specifications GeneralPhysical and Environment 2. What can I do if I don’t know or forgot my password? Appendix B Troubleshooting3. What can I do if I cannot access the web-based configuration page? For Windows XP OS Click Network Connections Right-click Local AreaConnection Click Properties Protocol TCP/IP Select Obtain an IP address automatically Double-click InternetClick OK Select Obtain DNS server address automatically Click OK For Windows Vista OS Click View network status and tasks Click View statusClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically For Windows 7 OS Click View network status and tasks Click Change adapter settingsRight-click Local Area Connection Click Properties Select Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet? 2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Global Appendix C Technical Support Technical SupportSingapore USA/Canada