CE Mark Warning, National Restrictions | TP-Link td-w8961nd guide

CE Mark Warning

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

National Restrictions

This device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:

	Country	Restriction	Reason/remark

	Bulgaria	None	General authorization required for outdoor use and
	Bulgaria	None	public service
			public service

Outdoor use limited to 10

FrancemW e.i.r.p. within the band 2454-2483.5 MHz

Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012

	Italy	None	If used outside of own premises, general authorization is
	Italy	None	required
			required

	Luxembourg	None	General authorization required for network and service
	Luxembourg	None	supply(not for spectrum)
			supply(not for spectrum)

	Norway	Implemented	This subsection does not apply for the geographical area
	Norway	Implemented	within a radius of 20 km from the centre of Ny-Ålesund
			within a radius of 20 km from the centre of Ny-Ålesund

	Russian Federation	None	Only for indoor applications

Note: Please don’t use the product outdoors in France.

This device has been designed to operate with the antennas listed below, and having a maximum gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.”

Image 4

TP-Link td-w8961nd manual CE Mark Warning, National Restrictions, Country, Reason/remark

Contents

TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router Rev 2.0.0 COPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENT CE Mark Warning National RestrictionsCountry Restriction DECLARATION OF CONFORMITY Product Description 300Mbps Wireless N ADSL2+ Modem RouterShenzhen, P. R. China ETSI EN 300 328 V1.7.1 Package Contents Hardware InstallationQuick Installation Guide Software Configuration Appendix A Specifications Appendix B TroubleshootingAppendix C Technical Support Maintenance 300Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsTD-W8961ND 1.2 Main Features WirelessChapter 1 Introduction 1.1 Product Overview 1.3 Conventions TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2 Hardware Installation 2.1 The Front PanelLED Explanation Name 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation EnvironmentBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 3 Quick Installation Guide 3.1 Configure PC TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button and Connection Type. Then click NEXT Step 5 Configure the rules for the WLAN, and click NEXT Step 6 Click NEXT to finish the Quick Start 4.1 Status Chapter 4 Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs ¾ Select Ethernet, and you will see the statistics table as below Statistics Table 4.2 Quick Start Please refer to 3.2 Login¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below 4.3 Interface Setup 4.3.1 Internet 1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4.3.2 LAN 4 Bridge Mode TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need How to assign a static IP address to the client? If you select Disabled, the DHCP function will not take effect 4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 2 WEP-128Bits 3 WPA-PSK 4 WPA2-PSK 5 WPA-PSK/WPA2-PSK 1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 4.4 Advanced Setup 4.4.1 Firewall 4.4.2 Routing 4.4.3 NAT 4.4.3.1 DMZ 4.4.3.2 Virtual Server Other operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 1 Assign VLAN PVID for each Interface 2 Define VLAN Group 4.4.6 ADSL 4.5 Access Management 4.5.1 ACL 4.5.2 Filter 4.5.2.1 IP Filter ¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry 4.5.2.2 MAC Filter To add a MAC Address filtering entry Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.3 Application Filter 4.5.2.4 URL Filter To add a URL filter entry 4.5.3 SNMP 4.5.4 UPnP 4.5.5 DDNS 4.5.6 CWMP 4.6 Maintenance 4.6.2 Time Zone 4.6.1 Administration1 NTP Server automatically 2 PC’s Clock 3 Manually 4.6.3 Firmware To upgrade the routers firmware, follow these instructions below To back up the Router’s current settings 3 The router will reboot after the upgrading has been finishedTo restore the Router’s settings 4.6.5 Diagnostics 4.6.4 SysRestart 4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment Appendix B Troubleshooting 2. What can I do if I don’t know or forgot my password?3. What can I do if I cannot access the web-based configuration page? For Windows XP OS Right-click Local Area Click Network ConnectionsConnection Click Properties Double-click Internet Protocol TCP/IP Select Obtain an IP address automaticallyClick OK Select Obtain DNS server address automatically TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Click View network status and tasks Click View status For Windows Vista OSClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Click View network status and tasks Click Change adapter settings For Windows 7 OSRight-click Local Area Connection Click Properties Select Obtain DNS server address automatically 4. What can I do if I cannot access the Internet? Click Internet Options Select Never dial a connection 2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Appendix C Technical Support Technical Support GlobalSingapore USA/Canada