Login | TP-Link td-w8961nd guide

1)Is the connection between your PC and the Router correct?

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router.

Figure 3-6

You can check it follow the steps below:

1)Is the connection between your PC and the Router correct?

The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit.

2)Is the TCP/IP configuration for your PC correct?

If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254.

3.2Login

Once your host PC is properly configured, please proceed as follows to use the Web-based Utility: Start your web browser and type the private IP address of the Router in the URL field: 192.168.1.1.

After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Start screen. You can follow the steps below to complete the Quick Start.

Figure 3-7

12

Image 19

TP-Link td-w8961nd manual Login, TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Contents

Rev 2.0.0 TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure Statement Restriction CE Mark WarningNational Restrictions Country ETSI EN 300 328 V1.7.1 DECLARATION OF CONFORMITYProduct Description 300Mbps Wireless N ADSL2+ Modem Router Shenzhen, P. R. China Software Configuration Package ContentsHardware Installation Quick Installation Guide Maintenance Appendix A SpecificationsAppendix B Troubleshooting Appendix C Technical Support 300Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsTD-W8961ND 1.1 Product Overview 1.2 Main FeaturesWireless Chapter 1 Introduction TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 Conventions Name Chapter 2 Hardware Installation2.1 The Front Panel LED Explanation 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation EnvironmentBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3 Quick Installation Guide TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? and Connection Type. Then click NEXT Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 6 Click NEXT to finish the Quick Start Step 5 Configure the rules for the WLAN, and click NEXT 4.1 Status Chapter 4 Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below 4.2 Quick StartPlease refer to 3.2 Login ¾ Select ADSL, and you will see the statistics table as below 4.3.1 Internet 4.3 Interface Setup 1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4 Bridge Mode 4.3.2 LAN TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect How to assign a static IP address to the client? 4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 3 WPA-PSK 2 WEP-128Bits 5 WPA-PSK/WPA2-PSK 4 WPA2-PSK 1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND 4.4.1 Firewall 4.4 Advanced Setup 4.4.2 Routing 4.4.3 NAT 4.4.3.2 Virtual Server 4.4.3.1 DMZ Other operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 2 Define VLAN Group 1 Assign VLAN PVID for each Interface 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management 4.5.2.1 IP Filter 4.5.2 Filter ¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.2 MAC Filter 4.5.2.3 Application Filter Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL Filter To add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP 4.5.6 CWMP 4.5.5 DDNS 4.6 Maintenance 4.6.2 Time Zone 4.6.1 Administration1 NTP Server automatically 3 Manually 2 PC’s Clock To upgrade the routers firmware, follow these instructions below 4.6.3 Firmware To back up the Router’s current settings 3 The router will reboot after the upgrading has been finishedTo restore the Router’s settings 4.6.4 SysRestart 4.6.5 Diagnostics 4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment For Windows XP OS Appendix B Troubleshooting2. What can I do if I don’t know or forgot my password? 3. What can I do if I cannot access the web-based configuration page? Right-click Local Area Click Network ConnectionsConnection Click Properties Select Obtain DNS server address automatically Double-click InternetProtocol TCP/IP Select Obtain an IP address automatically Click OK Click OK Click View network status and tasks Click View status For Windows Vista OSClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically Area Connection Click Properties Click View network status and tasks Click Change adapter settingsFor Windows 7 OS Right-click Local Select Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet? 2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step USA/Canada Appendix C Technical Support Technical SupportGlobal Singapore