The Back Panel | TP-Link td-w8961nd specs

2.2The Back Panel

TD-W8961ND300Mbps Wireless N ADSL2+ Modem Router User Guide

2.2The Back Panel

Figure 2-2

¾POWER: The Power plug is where you will connect the power adapter.

¾ON/OFF: The switch for the power.

¾WPS: The switch for the WPS function. For details, please refer to 4.3.3.1 Wireless-WPS Settings.

¾RESET: There are two ways to reset the Router's factory defaults.

Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings.

Method two: Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility.

¾WiFi: The switch for the WiFi function.

¾1, 2, 3, 4 (LAN): Through the port, you can connect the Router to your PC or the other Ethernet network devices.

¾ADSL: Through the port, you can connect the router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4 Connecting the Router.

¾Antennas: Used for wireless operation and data transmit.

6

Image 13

TP-Link td-w8961nd manual The Back Panel, TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide

Contents

Rev 2.0.0 TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure Statement National Restrictions CE Mark WarningCountry Restriction Product Description 300Mbps Wireless N ADSL2+ Modem Router DECLARATION OF CONFORMITYShenzhen, P. R. China ETSI EN 300 328 V1.7.1 Hardware Installation Package ContentsQuick Installation Guide Software Configuration Appendix B Troubleshooting Appendix A SpecificationsAppendix C Technical Support Maintenance 300Mbps Wireless N ADSL2+ Modem Router User Guide Package ContentsTD-W8961ND Wireless 1.2 Main FeaturesChapter 1 Introduction 1.1 Product Overview TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 1.3 Conventions 2.1 The Front Panel Chapter 2 Hardware InstallationLED Explanation Name 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now 2.2 The Back Panel 2.4 Connecting the Router 2.3 Installation EnvironmentBack to LED Explanation TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide 3.1 Configure PC Chapter 3 Quick Installation Guide TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide Step 4 Configure the IP address as Figure 3-4 shows. After that, click OK 2 Is the TCP/IP configuration for your PC correct? 3.2 Login1 Is the connection between your PC and the Router correct? and Connection Type. Then click NEXT Step 1 Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button Step 6 Click NEXT to finish the Quick Start Step 5 Configure the rules for the WLAN, and click NEXT 4.1 Status Chapter 4 Software Configuration4.1.1 Device Info 4.1.2 System Log Click the CLEAR LOG button to clear the logs 4.1.3 StatisticsClick the SAVE LOG button to save the logs Statistics Table ¾ Select Ethernet, and you will see the statistics table as below Please refer to 3.2 Login 4.2 Quick Start¾ Select ADSL, and you will see the statistics table as below ¾ Select WLAN, and you will see the statistics table as below 4.3.1 Internet 4.3 Interface Setup 1 Dynamic IP Address 2 Static IP Address 3 PPPoA/PPPoE 4 Bridge Mode 4.3.2 LAN TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide IGMP Snoop Enable the IGMP Snoop function if you need If you select Disabled, the DHCP function will not take effect How to assign a static IP address to the client? 4.3.3 Wireless TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide ¾ Multiple SSIDs Settings These are the settings of the SSID 1 WEP- 64Bits 3 WPA-PSK 2 WEP-128Bits 5 WPA-PSK/WPA2-PSK 4 WPA2-PSK 1 PBC 4.3.3.1 WPS SettingsMethod One Method Two 2 PIN code TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide TD-W8961ND 4.4.1 Firewall 4.4 Advanced Setup 4.4.2 Routing 4.4.3 NAT 4.4.3.2 Virtual Server 4.4.3.1 DMZ Other operations for the entries as shown in Figure To add a virtual server entry4.4.3.3 IP Address Mapping To add a mapping rule 4.4.4 QoSIP Address Mapping is only available for VCs with Multiple IPs ¾ Summary Click the button to view the configurations of QoS 4.4.5 VLAN 2 Define VLAN Group 1 Assign VLAN PVID for each Interface 4.4.6 ADSL 4.5.1 ACL 4.5 Access Management 4.5.2.1 IP Filter 4.5.2 Filter ¾ Interface Select the interface for the entry To add an IP Address filtering entry Step 5 Finally, click the SAVE to save the entry To add a MAC Address filtering entry 4.5.2.2 MAC Filter 4.5.2.3 Application Filter Select the “MAC” as the Rule Type on the Filter screen show in Figure 4.5.2.4 URL Filter To add a URL filter entry 4.5.4 UPnP 4.5.3 SNMP 4.5.6 CWMP 4.5.5 DDNS 4.6 Maintenance 4.6.2 Time Zone 4.6.1 Administration1 NTP Server automatically 3 Manually 2 PC’s Clock To upgrade the routers firmware, follow these instructions below 4.6.3 Firmware To back up the Router’s current settings 3 The router will reboot after the upgrading has been finishedTo restore the Router’s settings 4.6.4 SysRestart 4.6.5 Diagnostics 4.7 Help TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router User Guide General Appendix A SpecificationsPhysical and Environment 2. What can I do if I don’t know or forgot my password? Appendix B Troubleshooting3. What can I do if I cannot access the web-based configuration page? For Windows XP OS Right-click Local Area Click Network ConnectionsConnection Click Properties Protocol TCP/IP Select Obtain an IP address automatically Double-click InternetClick OK Select Obtain DNS server address automatically Click OK Click View network status and tasks Click View status For Windows Vista OSClick Properties Protocol Version 4 TCP/IPv4 Select Obtain an IP address automatically For Windows 7 OS Click View network status and tasks Click Change adapter settingsRight-click Local Area Connection Click Properties Select Obtain DNS server address automatically Click Internet Options Select Never dial a connection 4. What can I do if I cannot access the Internet? 2 Check to see if you can log on to the web management page of the Modem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step Global Appendix C Technical Support Technical SupportSingapore USA/Canada