Novatel OM-AD-0020 LOGS

Appendices

Test Bed Receiver Subsystem Addendum – Rev 1 33

LOGS

RCCA RECEIVER CONFIGURATION

This log outputs a list of all current GPSCard command settings. Obser ving this log is a good way to monitor the

GPSCard configuration settings. See RCCA in the MiLLennium Command Descriptions Manual for the RCCA default

list.

The following are the default parameters, for the TESTBEDW receiver, that are different than the standard Millenium

WAAS receiver configuration:

CLOCKADJUST DISABLE

EXTERNALCLOCK OCXO

LOG CONSOLE TM1A ONTIME 10 HOLD*

* The logging of the TM1A log is done in order to time synchronize the TESTBEDGLO receiver to the

TESTBEDW receiver.

The following are the default parameters, for the TESTBEDGLO receiver, that are different than the standard Millenium

Glonass receiver configuration:

CLOCKADJUST DISABLE

EXTERNALCLOCK OCXO

SETTIMESYNC ENABLE*

* The SETTIMESYNC ENABLE allows the TESTBEDGLO receiver to accept the TM1A logs from the

TESTBEDW receiver for time synchronization.

Contents

Main Test Bed Receiver Subsystem Addendum Proprietary Notice TABLE OF CONTENTS Page TABLES Page FOREWORD SCOPE PREREQUISITES 1 INTRODUCTION THE NOVATEL TEST BED RECEIVER 1 - Introduction Test Bed Receiver Subsystem Addendum Rev 1 9 OPERATIONAL OVERVIEW L1/L2-I L1/L2-II GEO Processing Single Frequency GPS GLONASS Dual Frequency GPS GEO Other Outputs & Inputs 2 INSTALLATION OF TEST BED RECEIVER MINIMUM CONFIGURATION INTERNAL AND EXTERNAL OSCILLATORS CONNECTING THE EXTERNAL FREQUENCY REFERENCE CONNECTING DATA COMMUNICATIONS EQUIPMENT DCD RXD TXD DTR GND DSR RTS CTS NC CONNECTING THE GPS ANTENNA CONNECTING THE EXTERNAL POWER INPUT USING THE 10 MHz OUTPUT SIGNAL Page 3 OPERATION PRE-START CHECK LIST SERIAL PORTS - DEFAULT SETTINGS START-UP INITIAL COMMUNICATIONS WITH THE TEST BED RECEIVER 4 UPDATE OR UPGRADE YOUR GPSCARD UPGRADING USING THE $AUTH COMMAND UPDATING USING THE LOADER UTILITY TRANSFERRING FIRMWARE FILES USING THE LOADER UTILITY A WAAS OVERVIEW B GLONASS OVERVIEW MILLENNIUM-GLONASS GPSCARD X GLONASS SYSTEM DESIGN The Space Segment The Control Segment The User Segment TIME GLONASS TIME VS. LOCAL RECEIVER TIME DATUM FUNCTIONAL OVERVIEW MILLENNIUM-GLONASS GPSCARD SYSTEM Reference Description Reference Description GPS/GLONASS ANTENNA RADIO FREQUENCY (RF) SECTION DIGITAL ELECTRONICS SECTION Page C COMMANDS CONFIG IONOMODEL WAASCORRECTION LOGS RCCA RECEIVER CONFIGURATION D GLONASS COMMANDS AND LOGS GLONASS-SPECIFIC COMMANDS DGLOTIMEOUT Syntax: Options: PZ90TOWGS84 Syntax: Options: Example: PZ90TOWGS84 DEFAULT UNIMPLEMENTED COMMANDS GLONASS-SPECIFIC LOGS CALA/B CALIBRATION INFORMATION CALA Page CALB Format: Message ID = 87 Message byte count = 32 + (16 * 32) GALA/B ALMANAC INFORMATION GALA GALB Format: Message ID = 78 Message byte count = 112 GCLA/B CLOCK INFORMATION GCLA Table 2 Time Status Example: $GCLA,994,149871.00,10787,10.62179349,167.82950123,1121, -3.0544738044739E-007,9,4,00000000*7B,[CR][LF]GCLB GCLB Format: Message ID = 88 Message byte count = 68 GEPA/B EPHEMERIS INFORMATION GEPA Example: $GEPA,991,496487.00,991,495913.00,10787,4,12,83,0,-2.102581933593754E+007 GEPB Format: Message ID = 77 Message byte count = 156 Page OTHER NOVATEL LOGS RCCA RECEIVER CONFIGURATION E TEST BED RECEIVER - TECHNICAL SPECIFICATIONS Page Appendices 50 Test Bed Receiver Subsystem Addendum Rev 1 Default Channel Assignments INDEX