Novatel OM-AD-0020 D GLONASS COMMANDS AND LOGS

Appendices

34 Test Bed Receiver Subsystem Addendum – Rev 1

D GLONASS COMMANDS AND LOGS

GLONASS-SPECIFIC COMMANDS

This chapter describes MiLLennium-GLONASS GPSCard commands important to GL ONASS.

GLONASS-specific commands are generated by using information obtained from the GLONASS satellite system. Please

see the following sections for definitions of these commands.

DGLOTIMEOUT

The differential GLONASS time out (DGLOTIMEOUT) command’s function is to set the maximum age of differential

data that will be accepted when operating as a remote station. Differential data received that is older than the specified

time will be ignored.

The ephemeris delay of the reference station is the same as for GPS and c an be set usi ng the DGPST IME OUT comm and

(refer to the MiLLennium Command Descriptions Manual for information on this command).

Since there is no Selective Availability (SA) on the GLONASS correction the degradation over time is considerably less.

It could be useful to allow a longer timeout for GLONASS than GPS.

Syntax:

DGLOTIMEOUT delay

Options:

delay: 2 - 1000 (seconds) (default 60)

Contents

Main Test Bed Receiver Subsystem Addendum Proprietary Notice TABLE OF CONTENTS Page TABLES Page FOREWORD SCOPE PREREQUISITES 1 INTRODUCTION THE NOVATEL TEST BED RECEIVER 1 - Introduction Test Bed Receiver Subsystem Addendum Rev 1 9 OPERATIONAL OVERVIEW L1/L2-I L1/L2-II GEO Processing Single Frequency GPS GLONASS Dual Frequency GPS GEO Other Outputs & Inputs 2 INSTALLATION OF TEST BED RECEIVER MINIMUM CONFIGURATION INTERNAL AND EXTERNAL OSCILLATORS CONNECTING THE EXTERNAL FREQUENCY REFERENCE CONNECTING DATA COMMUNICATIONS EQUIPMENT DCD RXD TXD DTR GND DSR RTS CTS NC CONNECTING THE GPS ANTENNA CONNECTING THE EXTERNAL POWER INPUT USING THE 10 MHz OUTPUT SIGNAL Page 3 OPERATION PRE-START CHECK LIST SERIAL PORTS - DEFAULT SETTINGS START-UP INITIAL COMMUNICATIONS WITH THE TEST BED RECEIVER 4 UPDATE OR UPGRADE YOUR GPSCARD UPGRADING USING THE $AUTH COMMAND UPDATING USING THE LOADER UTILITY TRANSFERRING FIRMWARE FILES USING THE LOADER UTILITY A WAAS OVERVIEW B GLONASS OVERVIEW MILLENNIUM-GLONASS GPSCARD X GLONASS SYSTEM DESIGN The Space Segment The Control Segment The User Segment TIME GLONASS TIME VS. LOCAL RECEIVER TIME DATUM FUNCTIONAL OVERVIEW MILLENNIUM-GLONASS GPSCARD SYSTEM Reference Description Reference Description GPS/GLONASS ANTENNA RADIO FREQUENCY (RF) SECTION DIGITAL ELECTRONICS SECTION Page C COMMANDS CONFIG IONOMODEL WAASCORRECTION LOGS RCCA RECEIVER CONFIGURATION D GLONASS COMMANDS AND LOGS GLONASS-SPECIFIC COMMANDS DGLOTIMEOUT Syntax: Options: PZ90TOWGS84 Syntax: Options: Example: PZ90TOWGS84 DEFAULT UNIMPLEMENTED COMMANDS GLONASS-SPECIFIC LOGS CALA/B CALIBRATION INFORMATION CALA Page CALB Format: Message ID = 87 Message byte count = 32 + (16 * 32) GALA/B ALMANAC INFORMATION GALA GALB Format: Message ID = 78 Message byte count = 112 GCLA/B CLOCK INFORMATION GCLA Table 2 Time Status Example: $GCLA,994,149871.00,10787,10.62179349,167.82950123,1121, -3.0544738044739E-007,9,4,00000000*7B,[CR][LF]GCLB GCLB Format: Message ID = 88 Message byte count = 68 GEPA/B EPHEMERIS INFORMATION GEPA Example: $GEPA,991,496487.00,991,495913.00,10787,4,12,83,0,-2.102581933593754E+007 GEPB Format: Message ID = 77 Message byte count = 156 Page OTHER NOVATEL LOGS RCCA RECEIVER CONFIGURATION E TEST BED RECEIVER - TECHNICAL SPECIFICATIONS Page Appendices 50 Test Bed Receiver Subsystem Addendum Rev 1 Default Channel Assignments INDEX