Numark Industries EM460 owner manual Crossfader

EM460

CROSSFADER

19.Replaceable Crossfader - achieves clean segues between the two input channels selected by the Crossfader Assign.

Note: The crossfader is a user replaceable item and subject to wear. Excessive force can wear out the fader quickly. This is not a warranted item. In case of failure. Simply unscrew the two large screws that hold it in place, lift it out and disconnect its cable. Re-attach the new crossfader and screw the mounting plate back onto the unit - you’re back in business!

20.Crossfader Assign Knob - determines which input channel will be heard when the crossfader is moved towards the knob. With the crossfader centered, both assigned channels are live. Use the crossfader for fast and seamless segues from one selected channel to the other.

21.Fader Start – activates the crossfader to send play and cue commands to your auto-start Numark CD player or other popular brand. For fader start, attach your mixer to a remote start CD player using industry standard 1/8”(3.5mm) cables. When you move the crossfader toward the active channel, the attached CD player will start. When it is moved away, that side will cue (similar to pressing the cue button).

KAOSS PAD*

22.Process buttons – send post channel fader audio to the KAOSS PAD for processing.

23.Process Blend Control – mixes processed (efx)-wetaudio with unprocessed (src)-dryaudio. Use this in conjunction with the KOASS pad to reach desired effects.

24.Preset Program keys (1–6)- You can assign programs to keys 1–6 for convenient selection.

Program assignment:

a)Press one of the PROGRAM MAP keys.

b)Use the PROGRAM knob to select the program that you wish to assign. If you wish to memorize the HOLD setting, turn the HOLD switch to ON after selecting the program, and touch the touch panel to specify the position.

c)Press and hold the PROGRAM MAP key you pressed in step 1 for approximately two seconds.

25.Touch panel- You can control the sound by using your finger to rub or tap (strike lightly) this panel. Never press down too hard on the touch panel, or place a heavy object on it. Rough handling can cause it to crack or break. Rubbing or pressing the touch panel with a sharp object can scratch it, so only use your finger to operate it. If cleaning is necessary, wipe only with a soft dry cloth. Using solvents such as thinner may melt the surface of the touch panel. Note: Affix the included protective label to extend product life.

26.Hold Switch- When this switch is ON, the current state of the effect will be maintained even if you remove your finger from the touch panel.

27.Program Knob- Use this knob to select programs (1–60). Please see page for a complete listing of effects.

28.Program/Location Display- This shows either the currently selected program number or the location of the point that you touched on the touch panel, depending upon mode.

•When selecting a program: the program number (1–60) will be displayed.

•When operating the touch panel: the position you touched (1.1–9.9) with 5.5 being the center) will be displayed.

29.EFX ON/OFF / Sample Record switch- This can be used to switch between the effect sound and the direct (unprocessed) sound, or to record a sample.

When sampling this button lets you record a phrase that you hear and then play it back by operating the touch panel.

Use the following procedure to record and playback samples.

•Using the PROGRAM knob or the PROGRAM MAP keys, select a sample/play effect (program numbers 51–60). The RECswitchLEDwillblink,andtheKAOSSPADwillbeinrecord-ready mode.Atthistime,thesoundwillbeoutputwithoutanychange.

•Press the REC switch to begin recording.

•Press the REC switch once again to stop recording. The REC switch LED will light. Even if you do not press the REC switch, recording will end automatically when the maximum recording time has elapsed. (The maximum recording time will depend on the program.)

•Operate the touch panel to playback the recorded phrase. The sound will change depending on the position where you touch the panel. The way in which the sound changes will depend on the program.

•To re-record, press the REC switch again. The previously recorded phrase will be erased, and a new phrase will be recorded.

If you change programs to a non-sample program, the recorded phrase will be erased.

Example display: 3.8

vertical position is (3) / horizontal position is (8)

If you select a program that has a Hold On setting, the

program number will be displayed, and then the position*KAOSS technology under license from KORG that is being held will be displayed.

- The Leader in DJ Technology

©2000Industries - 5 - http://www.numark.com