PREPARING THE RECEIVER
REMOVING THE RECEIVER COVER
Refer to Figure 5.
1. Press the two locking tabs located on the bottom of the Receiver cover, and lift cover from base.
2. Set chime cover aside.
MOUNTING OF RECEIVER | “PUSH” TO OPEN | ||
Refer to Figure 6. |
| FIGURE 5 | |
Receiver may be used as |
|
| |
a portable receiver or may |
| 1/8" | |
be wall mounted. Use the |
|
| |
following procedure when | CHIME |
| |
mounting the Receiver to |
| ||
RECEIVER | |||
the wall. | |||
|
| ||
1. Select the desired |
|
| |
mounting location. This |
| KEYHOLE | |
location should be at least 1 |
| SLOT | |
foot away from metal |
| FIGURE 6 | |
objects and within 100 feet |
| ||
of the chime transmitter. |
|
|
2.Drill one 3⁄16" hole at the desired mounting height.
3.Insert the plastic anchor into the 3⁄16" hole.
4.Drive the upper screw into the plastic anchor until the head of the screw extends approximately 1⁄8" from the mounting surface.
5.Place the keyhole slot in the receiver base over the screw head. Slide the Receiver down to secure it.
6.Level the chime receiver on the mounting surface.
7.Mark the mounting surface with a pencil at the center of the oval hole in the bottom of the receiver base.
8.Gently remove the chime base from the mounting surface and drill one 3⁄16" hole at the previously marked area.
9.Insert the plastic anchor into the 3⁄16" hole and remount the chime receiver.
10.Insert the screw through the chime base into the plastic anchor. Level chime base and tighten screw.
RECEIVER SECURITY CODING
ATTACHING THE RECEIVER COVER
Position chime cover over chime base. Align locking tabs on bottom of cover to bottom of chime receiver base. Firmly press chime cover onto chime base.
TROUBLESHOOTING GUIDE
|
|
|
|
|
|
| PROBLEM | SOLUTION |
|
| 1. | Chime does not sound. | Check batteries and polarity. |
|
|
|
| Make sure receiver or transmitter |
|
|
|
| is not located on metal surface. |
|
|
|
| Check receiver and transmitter security |
|
|
|
| code. These codes must match. |
|
|
|
|
|
|
| 2. | Chime changes tone. | Check batteries in receiver. |
|
|
|
|
|
|
| 3. | Chime looses volume. | Check batteries in receiver. |
|
|
|
|
|
|
| 4. | Chime is activated by another | Change the security code in the transmitter |
|
|
| wireless device. | and receiver. These codes must match. |
|
|
|
|
|
|
| 5. | When transmitter button is pressed, | Check the sound code jumpers |
|
|
| the incorrect chime sound is heard. | in the transmitter. |
|
|
|
|
|
|
|
|
|
|
|
One Year Limited Warranty
WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to
Refer to Figure 7.
Changing the Security code is not necessary unless you have changed the security code
in the transmitter.
Both the transmitter and receiver codes must match.
1.Remove the same jumpers in the receiver as in the transmitter.
SECURITY CODE |
|
|
|
SETTING & VOLUME |
|
|
|
| VOLUME |
| |
| CONTROL |
| |
1 | CODE |
|
|
2 |
|
| |
SETTING |
| ||
3 |
|
|
|
4 |
|
|
|
5 |
|
|
|
6 | ON | OFF |
|
|
| ||
POWER | + |
| + |
SWITCH |
| – | – |
| – |
| – |
|
| + | + |
4 – “D” SIZE |
|
|
|
BATTERIES |
|
| FIGURE 7 |
|
|
|
misuse, negligence, accident, improper maintenance or repair (other than by NuTone), faulty installation or installation contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one year period as specified for the express warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY SERVICE: To qualify for warranty service, you must (a) notify NuTone at the address stated below or telephone
Date of InstallationBuilder or Installer
INSTALLING BATTERIES IN RECEIVER
Refer to Figure 7.
Refer to Figure 7 for placement and polarity of batteries.
The NuTone wireless chime receiver requires four “D” size alkaline batteries.
ADJUSTING THE RECEIVER VOLUME
Refer to Figure 7.
1.Slide power switch to the ON position.
2.Press Transmitter button. The red light on the Transmitter will light.
3.Adjust volume control to desired sound level. To increase volume, turn the control clockwise.
Model No. and Product Description
IF YOU NEED ASSISTANCE OR SERVICE:
For the location of your nearest NuTone Independent Authorized Service Center:
Residents of the contiguous United States Dial Free
Please be prepared to provide:
Product model number • Date and Proof of purchase • The nature of the difficulty Residents of Alaska or Hawaii should write to: NuTone Inc. Attn: Department of National Field Service, 4820 Red Bank Road, Cincinnati Ohio
Residents of Canada should write to:
Rev. 01/2005
Product specifications subject to change without notice.
4820 Red Bank Road, Cincinnati, Ohio 45227 Printed in China, Rev. 9/06, Part No. 85766