Omega Vehicle Security DP63000A-I ZErO, dSP-t, d-LEV, ScroL, COLOr, rEd 6rn, yES NO, 1 to, CodE, UNItS, rEd, dSP, DISPLAY UPDATE TIME, FRONT PANEL DISPLAY SELECT ENABLE (SEL), dSP, 000 to, OFF

6.3MODULE 3 - DISPLAY AND FRONT PANEL BUTTON PARAMETERS (3-dSP)

PARAMETER MENU

		DISPLAY UPDATE TIME
dSP-t	«	0.5	1	2	seconds
ª
	1

This parameter sets the display update time in seconds.FRONT PANEL DISPLAY SELECT ENABLE (SEL)

DISPLAY COLOR (BACKLIGHT UNIT ONLY)

COLOr		«
			rEd 6rn
ª
	rEd

Enter the desired display color, red or green. This parameter is active for backlight units only.

SEL		«
ª			yES NO
	yES

The yES selection allows the SEL button to toggle through the enabled displays.FRONT PANEL RESET ENABLE (RST)

rSt		«	NO	LO	dSP
			HI	HI-LO
ª
	dSP

This selection allows the RST button to reset the selected value(s).ZERO DISPLAY WITH DISPLAY RESET

ZErO	«
ª	NO	yES NO

This parameter enables the RST button or user input to zero the input display value, causing the display reading to be offset.

Note: For this parameter to operate, the RST button or User Input being used must be set to dSP and the Input value must be displayed. If these conditions are not met, the display will not zero.

DISPLAY INTENSITY LEVEL (BACKLIGHT UNIT ONLY)

d-LEV	«	1 to 5
ª
	5

Enter the desired Display Intensity Level (1-5). The display will actively dim or brighten as levels are changed. This parameter is active for backlight units only.

PROGRAMMING SECURITY CODE

CodE		«	000 to 999
ª
	000

The Security Code determines the programming mode and the accessibility of programming parameters. This code can be used along with the Program Mode Lock-out (P-Loc) in the User Input Function parameter (Module 1).

Two programming modes are available. Full Programming mode allows all parameters to be viewed and modified. Quick Programming mode permits only the Setpoint values to be modified, but allows direct access to these values without having to enter Full Programming mode.

Programming a Security Code other than 0, requires this code to be entered at the CodE prompt in order to access Full Programming mode. Depending on the code value, Quick Programming may be accessible before the CodE prompt appears (see chart).

DISPLAY SCROLL ENABLE

ScroL	«
ª	NO	yES NO

The yES selection allows the display to automatically scroll through the enabled displays. The scroll rate is every 4 seconds. This parameter only appears when the MAX or MIN displays are enabled.

UNITS INDICATOR SELECTION

UNItS		«
ª			OFF	LISt	SEGS
	OFF

This parameter activates the Units Indicator on the display. There are two methods of selecting the Indicator. List will present a group of Units preprogrammed into the meter. Segments allows the user to choose which of the segments should light.

USER INPUT	USER INPUT	SECURITY	MODE WHEN “SEL”	FULL PROGRAMMING
FUNCTION	STATE	CODE	BUTTON IS PRESSED	MODE ACCESS
		0	Full Programming	Immediate Access
		1-99	Quick Programming	After Quick Programming
not P-Loc	______			with correct code entry
				at CodE prompt *
		100-999	CodE prompt	With correct code entry
				at CodE prompt *
		0	Programming Lock	No Access
P-Loc	Active	1-99	Quick Programming	No Access
		100-999	CodE prompt	With correct code entry
				at CodE prompt *
	Not Active	0-999	Full Programming	Immediate Access

* Entering Code 222 allows access regardless of security code.

11