Omron CJ-Series manual Sequence Control, Field Terminals

List of Function Blocks

Type	Block Name	Function
Signal Selec-	Rank Selector	Selects the rank of up to 8 analog signals.
tion/Switching	(See note 1.)
	Input Selector	Selects the specified analog signals specified by
	(See note 1.)	the contact signal from up to 8 analog signals.
	3-input Selector	Selects and outputs one of three analog input
	(See note 1.)	signals.
	3-output Selector	Outputs one analog input signal in three switched
	(See note 1.)	directions.
	Constant Selector	Selects 8 preset constants by the contact signal.
	(See note 1.)
	Constant Generator	Outputs 8 independent constants.
	(See note 1.)
	Ramped Switch	Switches two analog inputs (or constants) with a
		ramp.
	Bank Selector	Records the PID parameters (SP, P, I, D, MH, ML)
		in up to 8 sets in advance, and switches the PID
		parameter for Basic/Advanced/Blended PID
		Blocks according to the analog input range
		(zone) or input bits.
	Split Converter	Inputs the MV from the Basic PID block or Ad-
		vanced PID block, converts the MV into two
		analog outputs for V characteristics or parallel
		characteristics (e.g., MV for heating or cooling)
		and outputs them.
Constant	Constant ITEM Setting	Writes the constant to the specified ITEM at the
ITEM Setting	(See note 1.)	rising edge of the send command contact.
	Variable ITEM Setting	Writes the analog signal to the specified ITEM at
	(See note 1.)	the rising edge of the send command contact.
	Batch Data Collector	Stores each of max. 8 analog inputs to buffer by
	(See note 1.)	a certain timing within sequential processing.
Pulse Train	Accumulated Value In-	Adds up to four accumulated value signals.
Operation	put Adder
	Accumulated Value Ana-	Multiplies analog signals by the accumulated
	log Multiplier	value signals.
	Accumulator for accu-	Converts 4-digit accumulated value signals to 8
	mulated value input	digits.
	Contact input/Accumu-	Counts low-speed contact pulses, and outputs
	lated value output	8-digit accumulated signals.
	Accumulated Value In-	Converts 4-digit accumulated value signals to
	put/Contact Output	low-speed contact pulses before they are output.
Others	Analog/Pulse Width	Changes the ON/OFF duration ratio in a constant
	Converter (See note 1.)	cycle duration so that it is proportional to the
		analog signal.
Sequence	Contact Distributor	Connect contact signals between function blocks
Operation		in a 1:1 connection.
	Constant Comparator	Compares up to eight sets of analog signals and
	(See note 1.)	constants, and outputs the comparison results as
		contacts.
	Variable Comparator	Compares up to eight pairs of analog signals,
	(See note 1.)	and outputs the comparison results as contacts.
	Timer (See note 1.)	2-stage output type addition timer for forecast
		values and reached values. Can also output the
		present value.
	ON/OFF Timer	Timer for performing ON-OFF operation at preset
	(See note 1.)	ON and OFF times.
	Clock Pulse	Outputs a clock pulse at the setting time interval
	(See note 1.)	for a single operation cycle.
	Counter (See note 1.)	2-stage output type addition timer for forecast
		values and arrival values. Can also output the
		current value.
	Internal Switch	Temporary storage contact for accepting relays in
	(See note 1.)	the Step Ladder Program block.
		Note: (One internal switch is already allocated
		as “temporary storage” in CX-Process
		Tool.)
	Level Check	Checks an analog input for 8 levels and outputs
	(See note 1.)	a contact corresponding to the level. The level
		number is also output as an analog value at the
		same time.
Contact Type	ON/OFF Valve Manipu-	Manipulates and monitors ON/OFF valves with
Control Target	lator	open/close limit switches.
	Motor Manipulator	Manipulates and monitors motor operation.
	Reversible Motor Manip-	Manipulates and monitors reversible motor
	ulator	operation.
	Motor Opening Manipu-	Inputs a target opening, and manipulates an
	lator	electric positional-proportional motor.
	Switch Meter	Manipulates and monitors multiple (up to 8)
	(See note 2.)	devices such as ON/OFF valves, motors, or
		pumps.

Note: 1. The Function Blocks dealing with high-speed operation (operation cycle: 0.01, 0.02, and 0.05 seconds is possible).

2.Cannot be used with the CJ1G-CPU45P-GTC.

Sequence Control

Type	Block Name	Function
---	Step Ladder Pro-	Performs logic sequence and step pro-
	gram (See note.)	gression control.

Note: The Function Blocks dealing with high-speed operation (oper- ation cycle: 0.01, 0.02, and 0.05 seconds is possible).

Field Terminals

Type	Block Name	Function
Contact	DI 8-point Terminal	Inputs 8 contacts from 8-point Input Unit.
I/O
	DI 16-point Terminal	Inputs 16 contacts from 16-point Input
(See note.)
		Unit.
	DI 32-point Terminal	Inputs 32 contacts from 32-point Input
		Unit.
	DI 64-point Terminal	Inputs 64 contacts from 64-point Input
		Unit.
	DO 8-point Terminal	Outputs 8 contacts from 8-point Output
		Unit.
	DO 16-point Termi-	Outputs 16 contacts from 16-point Output
	nal	Unit.
	DO 32-point Termi-	Outputs 32 contacts from 32-point Output
	nal	Unit.
	DO 64-point Termi-	Outputs 64 contacts from 64-point Output
	nal	Unit.
	DI 16-point/Do	Inputs and outputs 16 contacts each from
	16-point Terminal	16-point Input/16-point Output Units.
Analog I/O	AI 4-point Terminal	Inputs 4 analog signals from CJ1W-
(See note.)	(PTS51)	PTS51 (Isolated-type Thermocouple
		Input Unit)
	AI 4-point Terminal	Inputs 4 analog signals from CJ1W-
	(PTS52)	PTS52 (Isolated-type Temperature Resis-
		tance Input Unit).
	AI 2-point Terminal	Inputs 2 analog signals from CJ1W-
	(PTS15/16, PDC15)	PTS15 (Isolated-type Thermocouple
		Input Unit), CJ1W-PTS16 (Isolated-type
		Temperature Resistance Input Unit), or
		CJ1W-PDC15 (Isolated-type DC Input
		Unit).
	AI 8-point Terminal	Inputs 8 analog signals from the CJ1W-
	(AD081)	AD081(-V1).
	AO 8-point Terminal	Outputs 8 analog signals from the CJ1W-
	(DA08V/C)	DA08V/DA08C.
	AI 4-point Terminal	Inputs 4 analog signals from the CJ1W-
	(AD041)	AD041(-V1).
	AO 4-point Terminal	Outputs 4 analog signals from the CJ1W-
	(DA041)	DA041(-V1).
	AO 2-point Terminal	Outputs 4 analog signals from the CJ1W-
	(DA021)	DA021.
	AI 4-point/AO 2-point	Inputs 4 analog signals and outputs 2 an-
	Terminal (MAD42)	alog signals each from the CJ1W-MAD42.
	AI 4-point Terminal	Inputs 4 analog signals from a DRT1-
	(DRT1-AD04)	AD04 DeviceNet Slave Analog Input Unit.
	AO 2-point Terminal	Outputs two analog signals from a DRT1-
	(DRT1-DA02)	DA02 DeviceNet Slave Analog Output
		Unit.
	AI 4-point Terminal	Inputs 4 analog signals from the CJ1W-
	(AD04U)	AD04U.
	AI 4-point Terminal	Inputs 4 analog signals from the CJ1W-
	(PH41U)	PH41U.

Note: The Function Blocks dealing with high-speed operation (operation cycle: 0.01, 0.02, and 0.05 seconds is possible).

13