Onkyo DR-2000 Using the Programmed Buttons

Programming the Remote Controller to Your TV

3

		SEND				LEARN
EEP			ON			STNBY
SL
			INPUT		S L
						E ECTOR
				MODE
			DVD			TA/MD
UDIO		ENING MODE							TV
A	IST					T – D
L		STEREO							A.
R
R									C
U										TR
S										L
				LE		ME	NU
		TIT
CH				ENTER					VOL
TUN
		R					P
			ET	URN		SE		R
REPEAT						/VC			MUTING
						TV
		A – B				DIMMER

4

One of the TV’s remote control buttons

Press one of the programmable buttons on the DVD Receiver’s remote controller.

The SEND/LEARN indicator goes off while the button is pressed, then lights up again.

Lights up again shortly after going off

		SEND		LEARN
	EEP	ON		STNBY
SL
		INPUT	S L
				E ECTOR
		MODE
		DVD		TA/MD
UDIO		ENING MODE			TV
A	ST			T – D
	LI	EREO

Proceed to the next step within 30 seconds.

To select another programmable button

Press one of the other programmable buttons within 30 seconds.

Press and hold the desired TV’s remote control button until the SEND/LEARN indicator flashes.

If the function is successfully copied, the SEND/LEARN indicator flashes twice.

•Flashes twice when the programming is successful.

•Flashes three times if the programming has failed.

•Flashes six times if the programming is failed because the data capacity of the programmable button has been exceeded. TV buttons whose data size overwhelms the capacity of the programmable buttons are

unable to be used for programming.

Resuming the factory settings for all the programmable buttons

1Press and hold MODE TV, then press SEARCH twice. The SEND/LEARN indicator flashes twice, then lights steadily.

Proceed to the next step within 30 seconds.

2Press MODE TV.

•When the factory settings resume, the SEND/LEARN indicator flashes twice.

•If failed, the SEND/LEARN indicator flashes three times. In this case, no change has been made to the programmable buttons.

If the programmed buttons do not operate properly

•If the SEND/LEARN indicator doesn’t light up when you press one of the programmed buttons, reprogram the button.

•If the remote controller operates only at a short distance or there is a slow response from the TV, check the batteries.

If the batteries are not weak, the pressed button is not properly programmed. Reprogram the button.

•If the remote controller remains without batteries for 10 minutes or more, the programmed data will be erased. In such a case, install new batteries, then reprogram the buttons.

Using the Programmed Buttons

		SEND	LEARN
	EEP	ON	STNBY
SL
		INPUT SELECTOR
		MODE
	O	DVD	TA/MD	TV
		ENING MODE
UDI
A	IST		T – D
	L	STEREO

		SEND			LEARN
EEP			ON		STNBY
SL
			INPUT SE LECTOR
				MODE
O			DVD		TA/MD			TV
		ENING MODE
UDI
A	IST				T – D
L		STEREO						A.
R
R								C
U									TR
S									L
				LE	ME	NU
		TIT
CH				ENTER				VOL
TUN
		R				P
			ET	URN	SE		R
REPEAT					/VC			MUTING
					TV
		A – B			DIMMER

Press MODE TV first, then press the programmed TV operation buttons.

TV

Programming another function to the programmed button

Carry out the steps from 1 to 4.

The previous function will be erased when the programming is successful.

Resuming the factory setting for a particular programmable button

After step 2, press the programmable button you wish to resume to the factory setting twice.

•When the factory setting resumes, the SEND/LEARN indicator flashes twice.

•If failed, the SEND/LEARN indicator flashes three times. In this case, no change has been made to the programmable button.

ON	S	TN
		BY

CH			VOL
TUN
		P
	U
T			R
SE
		C
/V
TV

MUTING

64