Onkyo DR-2000 Preparing the Remote Controller, Inserting the Batteries, Using the Remote Controller

Preparing the Remote Controller

Inserting the Batteries

1Detach the battery cover.

2Insert the two size AA/R6/UM3 batteries.

Be sure to match the + and – ends of the batteries with the diagram inside the battery compartment.

3 Attach the battery cover.

1 2 3

Notes

• When the batteries are getting weak, the SEND/	SEND/LEARN
LEARN indicator on the remote controller starts	indicator
flashing. In this case, replace the batteries with
new ones.		SEND	LEARN
For the other functions of this indicator, see
“Pointing the remote controller in the right
direction” on the right, and page 63.	P	ON	STNBY
	LEE
	S
		S L
• Do not mix new batteries with old batteries or		INPUT	E ECTOR
		MODE
			T
different kinds of batteries.		DVD	A/MD		TV
	UDIO	ENING MODE
	A IST		T – D
	L	STEREO			A.
	R
	R				C
• To avoid corrosion, remove the batteries if the	U					TR
	S					L
		E	M	ENU
		TITL

remote controller is not to be used for a long time.

• Remove dead batteries immediately to avoid damage from corrosion. If the remote controller does not operate smoothly, replace both batteries at the same time.

• The life of the supplied batteries is about six months but this varies depending on usage.

Using the Remote Controller

Switching the remote controller function modes

Some buttons on the remote controller have two or more functions. To set the functionality of these buttons, press one of the four MODE (AUDIO, DVD, TA/MD, TV) buttons in advance.

The function mode remains the same until another MODE button is pressed.

(Details about the functions and the related function modes are explained in each section.)

EEP	ON		STNBY
SL
	INPUT SELECTOR
UDI		MODE			TV		MODE buttons
	ENING MODE
O	DVD		TA/MD
A IST
L	STEREO T – D				A.
R
R					C
U						TR
S						L
		LE	ME	NU
	TIT
								MODE
CH		ENTER			VOL				TA/
TUN								D		M
							V
							D			D
	RET			UP			IO			T
		URN	SET R
			/VC				U
REPEAT			TV		MUTING		D			V
	A – B		DIMMER				A
REC				OPEN/CLOSE			Press MODE DVD first before operating
RANDOM					SLOW		the built-in DVD player.
SUBTITLE – ON / OFF ANGLE					ZOOM

	MODE
	D	TA/	M
V
D			D
IO			T
D			V
U
A

Press MODE AUDIO first before operating the speaker setting and sound related operations.

	MODE
	D	TA/	M
V
D			D
IO			T
D			V
U
A

Press MODE TA/MD first before operating the Onkyo MD recorder or z-connected cassette tape deck (see pages 12 and 31).

Press MODE TV first before operating your TV.

To operate the TV with the supplied remote controller, you need to let the remote controller learn the TV remote control signals (see pages 31 and 63).

Pointing the remote controller in the right direction

Point the remote controller toward the remote control sensor.

This indicator is SEND/LEARN

lit while any	indicator		Remote control sensor
button on the
remote controller	SEND	LEARN
is pressed.
	ON	STNBY
	EEP
	SL
	INPUT SE LECTOR
	MODE
	DVD	TA/MD
							eet)
		30˚				(16	f
		30˚			m
				5
			About

Notes

•Place the unit away from strong light such as direct sunlight or inverted fluorescent light which can prevent proper operation of the remote controller.

•Using another remote controller of the same type in the same room or using the unit near equipment which uses infrared rays may cause operational interference.

•Do not put any object (such as a book) on the remote controller. The buttons of the remote controller may be pressed by mistake and drain the batteries.

•Make sure the audio rack doors do not have colored glass. Placing the unit behind such doors may prevent proper remote controller operation.

•If there is any obstacle between the remote controller and the

remote control sensor, the remote controller will not operate.

8