Customizing the Remote Controller toYour TV
You can customize the supplied remote controller
2 | Place both the DVD Receiver’s |
remote controller and the TV’s |
SENDING/ |
| LEVEL SETUP | ||
LEARNED | DVD RECEIVER TV |
| ||
POWER | SLEEP | DIMMER DISPLAY | ||
ON | STANDBY | |||
TITLE |
| MENU | SURROUND MODE | |
| ENTER |
| INPUT SELECTOR | |
|
| DVD | TV | |
RETURN |
| SETUP | VIDEO 1 | TAPE |
CH SEL |
|
| VIDEO 2 | TUNER |
1 | 2 | 3 |
|
|
TEST | LEVEL |
| AUDIO | SUBTITLE |
TONE |
| |||
4 | 5 | 6 |
|
|
|
|
| ANGLE | ZOOM |
SENDING/LEARNED indicator
POWER ON
LEVEL SETUP
DVD RECEIVER | DVD RECEIVER/ |
| LEVEL SETUP/TV switch |
The following programmable buttons control the TV when the switch is set to TV.
remote control facing with each |
other on a flat level surface. |
TV’s remote control |
DVD Receiver's | Must be 5 cm to 10 cm |
7 8 9
OPEN/
SEARCH CLEAR CLOSE
+10 | 0 |
|
|
|
FR | PAUSE | FF | POWER | MUTING |
DOWN | PLAY | UP | CHANNEL | TV/ VCR |
| ||||
|
|
| TUNER |
|
RANDOM | STOP | SLOW | PRESET |
|
POWER MUTING
TV/VCR
remote controller | apart |
REPEAT | VOLUME |
REMOTE CONTROLLER | |
MEMORY |
|
CHANNEL |
TUNER |
PRESET |
TV/ VCR
VOLUME |
(When the switch is set to DVD RECEIVER, this button operates the muting function. See page 29.)
VOLUME /CHANNEL / (When the switch is set to DVD RECEIVER, this button is used to select the preset channels. See page 27.)
3 | MEMORY | Press MEMORY. |
| Proceed to the next step within 15 | |
|
| seconds. |
4 | POWER MUTING | Press one of the programmable |
|
| |
| CHANNEL TV/ VCR | buttons on the DVD Receiver’s |
|
| remote controller. |
| TUNER | The SENDING/LEARNED indicator lights |
| PRESET | up. |
|
| |
| VOLUME |
|
Programming the Remote Controller
Programming is carried out by copying the signal patterns of the TV’s remote control buttons.
Before programming the remote controller
•Use new batteries for the remote controller and the TV’s remote control. Using old batteries may result in a failure in programming or cause the programmed remote controller buttons to operate improperly.
•The remote controller and most of other remote controls transmit infrared rays, however, if the other remote control uses another method, programming is impossible.
•Although six buttons are prepared for operating the TV, the number of programmable buttons varies depending on the manufacturer and type of the other remote control.
•Turn off both the DVD Receiver and TV to prevent the units from undesired operation during programming.
•The remote control buttons on some TVs may have more than one function; however, only one function can be programmed per button.
•Refer also to the TV’s instruction manual for details on its remote control operation and other information.
Note
The programmed buttons of the DVD Receiver's remote controller may lose their data if the batteries become weak or dead, or due to other causes. In such a case, you need to repeat programming from the beginning using the TV's remote control. Therefore, keep the TV's remote control in a safe place even if it is not in use.
| 1 |
|
|
|
| Set the DVD RECEIVER/LEVEL | |
| LEVEL SETUP | SETUP/TV switch to TV. | |||||
|
| DVD RECEIVER |
| TV |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
5 | While the SENDING/LEARNED | |
| ||
One of the TV’s | indicator is lit, press the desired | |
TV’s remote control button whose | ||
remote control | ||
function you wish to copy. | ||
buttons | ||
| If the function is successfully copied, the | |
| SENDING/LEARNED indicator goes off. | |
| Repeat steps 3 to 5 to program other | |
| programmable buttons. | |
| Note | |
| If programming has failed because the data | |
| capacity of the programmable button has been | |
| exceeded or other reasons, the indicator flashes | |
| for five seconds. |
If the programmed buttons do not operate properly
•If the SENDING/LEARNED indicator doesn’t light up when you press one of the programmed buttons, reprogram the button.
•If the remote controller operates only at a short distance or there is a slow response from the TV, check the batteries.
If the batteries are not weak, the pressed button is not properly programmed. Reprogram the button.
•If the remote controller remains without batteries for 30 minutes or more, the programmed data will be erased. In such a case, install new batteries, then reprogram the buttons.
Erasing all the programmed functions
1Press MEMORY.2Within 5 seconds, press and hold POWER ON, then press and hold MEMORY at the same time until the SENDING/LEARNED indicator goes off.
60