Troubleshooting Guide

•No power.

Cause: Power cable is not properly plugged into the AC outlet. Remedy: Insert the power plug firmly.

•A disc is loaded in the disc tray, but playback will not start. Cause: A disc in the disc tray may be upside down.

Remedy: Load the disc with the label facing upward. Cause: The disc is dirty.

Remedy: Clean the disc.

Cause: Moisture has accumulated inside the CD changer. Remedy: Remove the disc from the disc tray, place the CD

changer in a warm place, and leave the power on for about one hour.

•No sound is heard.

Cause: Connections may be incomplete or incorrect.

Remedy: Check all cable connections. Insert all the plugs firmly into the jacks.

Cause: The input selector switch on the amplifier may be set incorrectly.

Remedy: Set the switch to the proper position. See your amplifier’s operating instructions for more informa- tion.

•Disc playback skips. Cause: The disc is dirty.

Remedy: Clean the disc. Cause: A disc is scratched.

Remedy: Replace the disc.

Cause: The CD changer is subject to being accidentally bumped.

Remedy: Place the CD changer in a more stable location.

•Search time (when locating a specific track) is extremely long. Cause: The disc is dirty.

Remedy: Clean the disc. Cause: The disc is scratched.

Remedy: Replace the disc.

•Track numbers cannot be stored in memory. Cause: No disc in the tray.

Remedy: Load a disc in the tray.

Cause: You have entered a track number that does not exist on the disc.

Remedy: Use only the track numbers that exist on the disc.

•Front panel controls function correctly, but remote control- ler does not.

Cause: No batteries in remote controller. Remedy: Insert batteries.

Cause: Batteries have worn out. Remedy: Replace batteries.

Specifications

Signal readout system:

Optical non-contact

Reading rotation:

About 500 - 200 r.p.m.

(constant linear velocity)

 

Linear velocity:

1.2 - 1.4 m/s

Error correction system:

Cross Interleave Reed-Solomon code

D/A converter:

1 bit PWM/ACCUPULSE

Sampling frequency:

352.8 kHz (8 times oversampling)

Number of channels:

2 (stereo)

Frequency response:

5 Hz - 20 kHz

Total harmonic distortion:

0.005% (at 1 kHz)

Dynamic range:

96 dB

Signal to noise ratio:

90 dB

Channel separation:

85 dB (at 1 kHz)

Wow and Flutter:

Below threshold of measurability

Output level:

2 volts r.m.s.

Power consumption:

9 watts

Power supply:

120 V, 60 Hz

 

230V, 50 Hz

 

220-230V/120V switchable, 50/60 Hz

Dimensions (W ⋅ H ⋅ D):

435 ⋅ 91 ⋅ 308 mm

 

(17-1/8" ⋅ 3-9/16" ⋅ 12-1/8")

Weight:

3.7 kg (8.2 lbs.)

Specifications and features are subject to change without notice.

This unit contains a sensitive microcomputer, which under certain circumstances might fail to operate due to excessive noise interfer- ence. In such case, switch off the main power by pressing the POWER switch, wait five seconds, then switch it on again.

Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 0720-31-8111 Fax: 0720-33-5222 http://www.onkyo-intl.com

ONKYO U.S.A. CORPORATION

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 201-785-2600 Fax: 201-785-2650 http://www.onkyousa.com

ONKYO EUROPE ELECTRONICS GmbH

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net

ONKYO CHINA LIMITED

 

Units 2102-7, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung,

HOMEPAGE

N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com

http://www.onkyo.co.jp/

16

 

 

E

 

SN 29342748

I9907-1