Onkyo HT-RC260 AV receiver’s remote controller doesn’t control your iPod, Can’t record

Make sure the correct input is selected on your TV or — the AV receiver.

Some versions of the iPod do not output video. —

■The AV receiver’s remote controller doesn’t control your iPod

Make sure your iPod is properly inserted in the	—
Dock. If your iPod is in a case, it may not connect
properly to the Dock. Always remove your iPod
from the case before inserting it into the Dock.

The iPod cannot be operated while it’s displaying the — Apple logo.

Make sure you’ve selected the right remote mode.	—
When you use the AV receiver’s remote controller,	—
point it toward your AV receiver.
When connecting UP-A1 Dock to the radio tuner	—
UP-HT1 with AUTO selected by the tuner’s Mode
Selector switch, you can switch the input source
between UP-A1 Dock and the tuner, by pressing
PORT repeatedly on the front panel.

If you still can’t control your iPod, start playback by — pressing your iPod’s Play button. Remote operation should then be possible.

Try resetting your iPod.	—
Depending on your iPod, some buttons may not	—
work as expected.

■The AV receiver unexpectedly selects your iPod as the input source

Always pause iPod playback before selecting a dif- — ferent input source. If playback is not paused, the Direct Change function may select your iPod as the input source by mistake during the transition between tracks.

Recording

■ Can’t record

On your recorder, make sure the correct input is	—
selected.
To prevent signal loops and damage to the AV	—
receiver, input signals are not fed through to outputs
with the same name (VCR/DVR IN to VCR/DVR
OUT).

Zone 2

■There’s no sound

Only components connected to analog inputs can be — played in Zone 2.

■The Zone 2 speakers produce no sound

Powered Zone 2 cannot be used if “Speakers Type” 35 is set to “Bi-Amp”.

To use the Zone 2 speakers, you must set the “Front 49 High/Front Wide/Zone2” setting to “Zone2”.

Others

■The sound changes when I connect my headphones

When a pair of headphones is connected, the listen- — ing mode is set to Stereo, unless it’s already set to Stereo, Mono or Direct.

■The speaker distance cannot be set as required

In some cases, corrected values suitable for home	—
theater use may be set automatically.

■How do I change the language of a multiplex source

Use the “Multiplex” setting on the “Audio Adjust” 37 menu to select “Main” or “Sub”.

■The ufunctions don’t work

To use u, you must make an uconnection and an 17 analog audio connection (RCA) between the compo- nent and AV receiver, even if they are connected dig- itally.

■The functions System On/Auto Power On and Direct Change don’t work for components connected via u

These functions don’t work when Zone 2 is turned 17 on.

■When performing “Audyssey 2EQ® Room Correction and Speaker Setup”, the measurement fails showing the message “Ambient noise is too high.”.

This can be caused by any malfunction in your	—
speaker unit. Check if the unit produces normal
sounds.

■The following settings can be made for the composite video inputs

You must use the buttons on the unit to make these set- tings.

1.While holding down the input selector button for the input source that you want to set, press SETUP.

2.Use e/rto change the setting.

3.Press the input selector button for the input source that you want to set when you’ve finished.

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, or AUX input.

If you have a games console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT:OFF: (default).

Video ATT:ON: Gain is reduced by 2 dB.

En

62