Connecting Onkyo uComponents, How to record the video

Note

*1	Connect a turntable (MM) that has built-in a phono preamp to TV/CD IN or connect it to PHONO IN with the phono preamp turned
	off. If your turntable (MM) doesn’t have a phono preamp, connect to PHONO IN. If your turntable has a moving coil (MC) type car-
	tridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s man-
	ual for details.
	If your turntable has a ground wire, connect it to the AV receiver’s GND screw. With some turntables, connecting the ground wire
	may produce an audible hum. If this happens, disconnect it.
*2	When you connect your personal computer to PC IN and select PC input selector, video of the personal computer is output from
	HDMI OUT. However, because the AV receiver selects the video input in the order of HDMI > component > analog RGB, if you
	have assigned HDMI IN to the PC input selector, the AV receiver will output signals from HDMI IN in priority to PC IN.
*3	To select the multichannel input, select the BD/DVD input selector and see “Audio Selector” (➔ 58). To adjust the subwoofer sensi-
	tivity for the multichannel input, see “Subwoofer Input Sensitivity” (➔ 43).

•The AV receiver can output audio and video signals from the AUX INPUT jacks to the VCR/DVR OUT jacks.

•With connection D, you can listen and record audio from the external components while you are in Zone 2. You can listen and record audio from the external components in the main room; you can listen to the audio in Zone 2 as well.

•With connection C, you can enjoy Dolby Digital and DTS. (To record or listen in Zone 2 as well, use C and D.)

■How to record the video

With the connections described above, you cannot record the video through the AV receiver. To make a connection for video recording (➔ 34).

Connecting Onkyo uComponents

Step 1:

Make sure that each Onkyo component is connected with an analog audio cable (connection D in the hookup examples) (➔ 19).

Step 2:

Make the uconnection (see illustration below).

Step 3:

If you’re using an RI Dock, or cassette tape deck, change the Input Display (➔ 27).

With u(Remote Interactive), you can use the following special functions:

■ System On/Auto Power On

Note

•Use only ucables for uconnections. ucables are supplied with Onkyo players (DVD, CD, etc.).

•Some components have two ujacks. You can connect either one to the AV receiver. The other jack is for connecting addi- tional u-capable components.

•Connect only Onkyo components to ujacks. Connecting other manufacturer’s components may cause a malfunction.

•Some components may not support all ufunctions. Refer to the manuals supplied with your other Onkyo components.

•While Zone 2 is on, the System On/Auto Power On and Direct Change ufunctions do not work.

•Do not use RI connections if you use HDMI Control (RIHD) (➔ 54).

When you start playback on a component connected via

uwhile the AV receiver is on Standby, the AV

receiver will automatically turn on and select that com-

ponent as the input source.

■ Direct Change

When playback is started on a component connected via

u, the AV receiver automatically selects that compo-

nent as the input source.

■ Remote Control

You can use the AV receiver’s remote controller to con-

trol your other u-capable Onkyo components, point-

ing the remote controller at the AV receiver’s remote

control sensor instead of the component. You must enter

the appropriate remote control code first (➔ 77).

REMOTE

CONTROL

e.g., CD player

e.g., DVD player

TV/CD

FRONT

BD/DVD

RL ANALOG

AUDIO OUT