Advanced Setup—Continued
Digital Input Signal Formats
The following table shows the display indicator for each digital signal format.
Format | Display | |||||
|
|
|
|
|
|
|
Dolby Digital |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
DTS |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PCM |
|
| PCM | |||
|
|
|
|
|
|
|
Normally, the AV receiver detects the signal format auto- matically. However, if you experience either of the fol- lowing issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS:
•If the beginnings of tracks from a PCM source are cut off, try the PCM setting.
•If noise is produced when fast forwarding or reversing a DTS CD, try the DTS setting.
Correcting Sound and Picture Sync
When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. You can set it from 0 to 100 milliseconds (ms) in 20 millisecond steps.
STANDBY/ON | REMOTE MODE | RECEIVER | |
| RECEIVER | DVD | |
| TAPE/AMP |
|
|
INPUT SELECTOR | M D/CDR |
| |
INPUT | 1 | 2 | 3 | CD |
|
|
| DOCK | |
VCR/DVR | CBL/SAT |
|
| |
SELECTOR | 4 | 5 | 6 | T V |
| AUX | MULTI CH | DVD |
|
| 7 | 8 | 9 | VCR |
| TAPE | TUNER | CD | CABLE |
| 10 | 11 | 12 | |
| +10 | 0 | CLR | SAT |
| D TUN | ENT |
|
|
| DIMMER | SLEEP |
| |
| TV | VOL | CH | VOL |
| DISC | |||
|
|
| ALBUM |
|
| INPUT |
|
|
|
| GUIDE |
| PREVIOUS | |
| TOP MENU |
|
| MENU |
SP A / B | MUTING |
ENTER
PLAYLIST/CATPLAYLIST/CAT
|
|
|
|
|
|
|
|
|
|
|
|
|
| MASTER VOLUME |
STANDBY/ON |
|
|
|
|
|
|
|
|
| TUNING | PRESET |
|
| |
STANDBY |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MULTI CH |
| DVD | VCR/DVR | CBL/SAT | AUX | TAPE | TUNER | C D | SETUP | ENTER | RETURN |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| AUX INPUT |
|
PHONES |
|
|
|
|
|
|
|
|
|
| SETUP MIC | VIDEO | L AUDIO | R |
A | SPEAKERS | B | TONE |
| STEREO | LISTENING MODE | DISPLAY DIGITAL INPUT | DIMMER | MEMORY TUNING MODE |
|
|
|
| |
DIGITAL INPUT
1 |
| Press and hold the AV receiver’s |
|
| |
| DIGITAL INPUT | [DIGITAL INPUT] button for about |
| 3 seconds. | |
|
| |
2 |
| While “Auto” is displayed (about |
|
| |
| DIGITAL INPUT | 3 seconds), press the [DIGITAL |
| INPUT] button repeatedly to | |
|
| |
|
| select: PCM, DTS, or Auto. |
PCM: Only PCM format input sig- nals will be heard. If the input signal is not PCM, the PCM indicator will flash and there will be no sound.
DTS: Only DTS format input sig- nals will be heard. If the input signal is not DTS, the DTS indicator will flash and there will be no sound.
Auto (default): The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.
SETUPRETURN
1 | Press the [RECEIVER] REMOTE |
| |
RECEIVER | MODE button. |
2 |
| Press and hold, for more than 4 | |
|
| ||
1 | 2 | seconds, the input selector but- | |
ton for the input source that you | |||
VCR/DVR CBL/SAT | |||
4 |
| 6 want to correct. | |
AUX |
| DVD | |
|
| This can be the [DVD], [VCR/DVR], | |
|
| [CBL/SAT], or [AUX] input source. | |
3 |
| Use the Left and Right [ ]/[ ] | |
buttons to adjust the delay from 0 to 100 milliseconds in 20 milli- second steps.
Note:
•This setting is not available when the Pure Audio lis- tening mode is used, or the Direct listening mode is used with an analog input signal.
61
