Onkyo TX-NR3008 instruction manual Speaker Distance

■Front

(Setting Speakers A and Speakers B)

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.

■Center*1, Surround*1, Surround Back*2*3*4*8

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None:

Select if no speaker is connected.

■Front Wide*1*2*6*7, Front High*1*2*5*7

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None:

Select if no speaker is connected.

Note

*1 “Full Band” can be selected only when “Full Band” is selected in the “Front” setting.

*2 If the “Surround” setting is set to “None”, this setting cannot be selected.

*3 If the “Surround” setting is set to anything other than “Full Band”, “Full Band” cannot be selected here.

*4 If the “Powered Zone 3” setting is set to “Act” (➔ 82), or “Bi-Amp” or “BTL” is being used (➔ 51), this setting cannot be selected.

*5 If the Powered Zone 2 is being used (➔ 82), this setting can- not be selected.

*6 If the “Powered Zone 2” setting is set to “Act” (➔ 82), this setting cannot be selected.

*7 If the “Speakers Type(Front B)” setting is set to “Normal”, “Bi-Amp” or “BTL” (➔ 51), this setting cannot be selected.

*8 This setting cannot be used if the “Front High + Front Wide” setting is set to “Yes”.

■Surround Back Ch

`1ch:

Select if only one surround back speaker is con- nected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

En

52

■Double Bass

This setting is NOT set automatically by Audyssey MultEQ® XT32 Room Correction and Speaker Setup function (➔ 32).

With the Double Bass function, you can boost bass out- put by feeding bass sounds from the front left, right, and center channels to the subwoofer.

`On:

Double Bass function on.

`Off(THX):

Double Bass function off.

Note

•This function can be set only if the “Subwoofer” setting is set to “1ch” or “2ch”, and the “Front” setting is set to “Full Band”.

•If you’re using THX-certified speakers, select “Off(THX)”.

■Subwoofer, Front, Center, Surround, Surround Back

(Setting Speakers A and Speakers B)

`Not Use:

Select if you don’t want to use each speaker with Speakers A or Speakers B.

`Use:

Select if you do want to use each speaker with Speakers A or Speakers B.

If you’re using Speakers B, you can choose whether or not to use the subwoofer, center, surround, and surround back speakers with the Speakers A and Speakers B configura- tions independently. You cannot choose whether or not to use the front speakers.

Note

•These settings can only be displayed when the “Speakers Type(Front B)” setting is set to other than “Not Use” (➔ 51).

•You cannot select speakers that you set to “No” or “None”.

Speaker Distance

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and Speaker Setup function (➔ 32). For Speakers B, you need to change the settings manually.

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

You can set the distances for front speakers A and front speakers B independently. The other speakers (i.e., sub- woofer, center, surround, and surround back) use the same distance settings for Speakers A and Speakers B.

■Unit

`feet:

Distances can be set in feet. Range: “0.5ft” to “30.0ft” in 0.5 foot steps.

`meters:

Distances can be set in meters. Range: “0.15m” to “9.00m” in 0.15 meter steps.

(The default setting varies from country to country.)