Onkyo TX-NR3008 instruction manual Enter

	TV
	d e f
	c a b
	g h
: Listening area	a to h: Listening position

Note

•Make the room as quiet as possible. Background noise and Radio Frequency Interference (RFI) can disrupt the room measure- ments. Close windows, televisions, radios, air conditioners, flu- orescent lights, home appliances, light dimmers, or other devices. Turn off the cell phone (even if it is not in use) or place it away from all audio electronics.

•The microphone picks up test tones which played through each speaker as Audyssey MultEQ® XT32 Room Correction and Speaker Setup run.

•Audyssey MultEQ XT32 Room Correction and speaker setup can only be used with Speakers A. When you insert the MIC with Speakers B selected, Speakers A will automatically be selected.

•Audyssey MultEQ XT32 Room Correction and speaker setup cannot be performed while a pair of headphones is connected.

1Turn on the AV receiver and the connected TV. On the TV, select the input to which the AV receiver

is connected.

2Set the speaker setup microphone at the Main Lis- tening Position a, and connect it to the SETUP

MIC jack.

SETUP MIC jack

Speaker setup microphone

The speaker setting menu appears.

3 When you’ve finished making the settings, press

ENTER.

MultEQ XT32: Auto Setup
Speakers Type(Front A)	Normal
Speakers Type(Front B)	Not Use
Powered Zone 2	Not Act
Powered Zone 3	Not Act

•If you change “Speakers Type(Front A)” or “Speakers Type(Front B)” setting, refer to “Speaker Settings” for more details (➔ 50).

•If you change “Powered Zone 2” or “Powered Zone 3” setting, refer to “Setting the Powered Zone 2/3” for more details (➔ 82).

•If you are using a subwoofer(s), select “1ch” or “2ch” in the “Subwoofer” (➔ 51). If not, select “No” and skip step 4.

4 If you use a powered subwoofer(s), adjust the sub- woofer volume level to 75dB.

Test tones are played through the subwoofer. Use the volume control on the subwoofer.

Caution

•When the “Subwoofer” setting is set to “1ch”, the left- hand subwoofer (SW1) alone will be measured.

When the “Subwoofer” setting is set to “1ch” with two subwoofers connected, the right-hand subwoofer (SW2) will not be measured and no sound will be output.

•An error will occur if you set “Subwoofer” to “2ch” with- out connecting any subwoofers, or with only one sub- woofer connected.

Note

•If your subwoofer does not have a volume control, disre- gard the level displayed and press ENTER to proceed to the next step.

•If you set the subwoofer’s volume control to its maximum and the displayed level is lower than 75 dB, leave the sub- woofer’s volume control at its maximum and press ENTER to proceed to the next step.

5 Press ENTER.

Audyssey MultEQ XT32 Room Correction and Speaker Setup starts.

Test tones are played through each speaker as Audyssey MultEQ XT32 Room Correction and Speaker Setup runs. This process takes a few min- utes. Please refrain from talking during measure- ments and do not stand between speakers and the microphone.

Do not disconnect the speaker setup microphone during Audyssey MultEQ XT32 Room Correction and Speaker Setup, unless you want to cancel the setup.

6 Place the setup microphone at the next position, and then press ENTER.

Audyssey MultEQ XT32 performs more measure- ments. This takes a few minutes.

7	When prompted, repeat step 6.
8	Use q/wto select an option, and then press

ENTER.

MultEQ XT32: Auto Setup
- -	Review Speaker Configuration - -
Subwoofer	2ch
Front	40Hz	TV
Center	40Hz
Surround	100Hz
Front Wide	None
Front High	100Hz
Surround Back	120Hz
Surround Back Ch	2ch
Save
Cancel

The options are:

`Save:

Save the calculated settings and exit

Audyssey MultEQ XT32 Room Correction and

Speaker Setup.

`Cancel:

Cancel Audyssey MultEQ XT32 Room Correc-

tion and Speaker Setup. En

33