Playing DTS program material, using the pause, fast — forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.
■The beginning of audio received by an HDMI IN can’t be heard
Since it takes longer to identify the format of an | — |
HDMI signal than it does for other digital audio |
|
signals, audio output may not start immediately. |
|
■There’s no sound during Whole House Mode
Make sure you’ve selected an analog audio input. | 47 |
Video
■ There’s no picture
Make sure that all video connecting plugs are pushed | 16 |
in all the way. |
|
|
|
Make sure that each video component is properly | 17, 18 |
connected. |
|
If your TV is connected to the HDMI output(s), | 46 |
select “- - - - |
|
composite video, |
|
sources. |
|
|
|
If the video source is connected to a component | 18, 45 |
video input, you must assign that input to an input |
|
selector, and your TV must be connected to either |
|
the HDMI output(s) or COMPONENT VIDEO |
|
MONITOR OUT. |
|
If the video source is connected to a composite video | 18 |
input, your TV must be connected to the HDMI |
|
output(s) or the corresponding composite video |
|
output. |
|
|
|
If the video source is connected to an HDMI input, | 17, 46 |
you must assign that input to an input selector, and |
|
your TV must be connected to the HDMI output(s). |
|
|
|
While the Pure Audio listening mode is selected, the — video circuitry is turned off and only video signals input through HDMI IN can be output.
On your TV, make sure that the video input to which — the AV receiver is connected is selected.
If the “Monitor Out” setting is set to “Both(Main)” — or “Both(Sub)” while your TV is connected to a secondary HDMI output (not a primary HDMI output), the picture may not appear. In this case, change the setting to “Both”.
■There’s no picture from a source connected to an HDMI IN
Reliable operation with an | 93 |
not guaranteed. In addition, video signals from a PC |
|
are not guaranteed. |
|
|
|
When the resolution is set to any resolution not | 46 |
supported by the TV, no video is output from the |
|
HDMI outputs. |
|
If the message “Resolution Error” appears on the | — |
AV receiver’s display, this indicates that your TV |
|
does not support the current video resolution and |
|
you need to select another resolution on your DVD player.
■The on-screen menus don’t appear
On your TV, make sure that the video input to which — the AV receiver is connected is selected.
When the AV receiver is not connected to a TV via — HDMI, onscreen menus are not displayed.
■The on screen display does not appear
Depending on the input signal, the on screen display 59 may not appear when the input signal from the
HDMI IN is output to a device connected to the
HDMI OUT MAIN.
Tuner
■Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light
Relocate your antenna. | — |
Move the AV receiver away from your TV or | — |
computer. |
|
Listen to the station in mono. | 28 |
|
|
When listening to an AM station, operating the | — |
remote controller may cause noise. |
|
Passing cars and airplanes can cause interference. | — |
|
|
Concrete walls weaken radio signals. | — |
|
|
If nothing improves the reception, install an outdoor — antenna.
Remote Controller
■ The remote controller doesn’t work
Before operating this unit, be sure to press | — |
RECEIVER. |
|
|
|
Make sure that the batteries are installed with the | 4 |
correct polarity. |
|
Install new batteries. Don’t mix different types of | 4 |
batteries, or old and new batteries. |
|
|
|
Make sure that the remote controller is not too far | 4 |
away from the AV receiver, and that there’s no |
|
obstruction between the remote controller and the |
|
AV receiver’s remote control sensor. |
|
Make sure that the AV receiver is not subjected to | — |
direct sunshine or |
|
Relocate if necessary. |
|
|
|
If the AV receiver is installed in a rack or cabinet | — |
with |
|
not work reliably when the doors are closed. |
|
Make sure you’ve selected the correct remote | 11, 75 |
controller mode. |
|
|
|
When using the remote controller to control other | — |
manufacturers’ AV components, some buttons may |
|
not work as expected. |
|
Make sure you’ve entered the correct remote control | 74 |
code. |
|
|
|
Make sure to set the same ID on both the AV | 59 |
receiver and remote controller. |
|
|
|
■ Can’t control other components
If it’s an Onkyo component, make sure that the u 20 |
| |
cable and analog audio cable are connected properly. |
|
|
Connecting only an ucable won’t be enough. |
|
|
Make sure you’ve selected the correct remote | 11, 75 | En |
controller mode. |
| |
|
| |
81
