the power switch, the power indicator light on the mount will glow red and the power indicator light on the hand controller will glow green. Your mount will now be moving at the sidereal rate, which is the same rate as the sky’s apparent motion. If the mount is properly polar aligned, it is now “tracking” the motion of astronomical objects as the Earth rotates.
To move your telescope to a new object, loosen both the R.A. and Dec. lock levers and move the telescope until it is pointed in the general direction of the object you wish to view. Retighten the R.A and Dec. lock levers. To center the object in the eyepiece’s field of view, you will usually need to use the hand controller.
There are four pushbuttons on the hand controller. If no but‑ tons are pushed, the R.A. motor will turn the R.A. axis at side‑ real rate to track the motion of the night sky. The left and right buttons move the mount about its R.A. axis, and the up and down buttons move the mount about its Dec. axis. The rate of speed is determined by the rate switch at the top right of the hand controller. If the switch is at the 2x position, the mount will move at two times sidereal rate when the right hand but‑ ton is pushed, which will cause objects to viewed in the eye‑ piece to move slowly eastward. If the left button is pushed, the drive will stop turning, which will cause objects in the eye‑ piece to move slowly westward. The top and bottom bottoms will cause the telescope to move north and south in declina‑ tion at the 2x speed. Similarly, if the switch is at the 8x or 16x position, the mount will move eight times or sixteen times sidereal rate when a button is pushed.
The 2x sidereal rate is the best setting for making guiding corrections during
Whenever any of the four buttons on the hand controller are pressed, the LED in the center of the controller will shine red; when the button is released, the LED will be green. Also, when the LED starts to blink at a constant rate, its time to change the batteries in the battery pack.
Using the R.A. and Dec. Reversal Switches
On the side of the hand controller, there are two reversal switches, one for the R.A. axis, and one for the Dec. axis.When these switches are flipped to the “REV” setting, the function of the pushbuttons on the hand controller will be reversed. The reversal switches allow you to orient the pushbuttons to the direction of the apparent movement of a guide star in a guide scope for astrophotography.
Understanding the Setting Circles
The setting circles on an equatorial mount (Figure 12) enable you to locate celestial objects by their “celestial coordinates”. Every object resides in a specific location on the “celestial sphere”. That location is denoted by two numbers: its right ascension (R.A.) and declination (Dec.). In the same way, every location on Earth can be described by its longitude and latitude. Right ascension is similar to longitude on Earth, and declination is similar to latitude. The R.A. and Dec. values for
Dec. setting circle
Dec. setting circle thumbscrew (2)
Dec. indicator arrow
R.A. setting circle
R.A. indicator arrow
R.A. setting circle thumbscrew (2)
Figure 12. The R.A. and Dec. setting circles.
celestial objects can be found in any star atlas or star cata‑ log.
The R.A. setting circle is scaled in hours, from 1 through 24, with small marks in between representing
The Dec. setting circle is scaled in degrees, with each mark representing 2° increments. Values of declination coordinates range from +90° to
So, the coordinates for the Orion Nebula listed in a star atlas will look like this:
R.A. 5h 35.4m Dec. – 5° 27'
That’s 5 hours and 35.4 minutes in right ascension, and
Before you can use the setting circles to locate objects, the mount must be accurately polar aligned, and the setting cir‑ cles must be calibrated.
Calibrating the Declination Setting Circle
1.Loosen the Dec. lock lever and position the telescope as accurately as possible in declination so it is parallel to the R.A. axis as shown in Figure 7.
2.Loosen one of the thumbscrews on the Dec. setting circle, this will allow the setting circle to rotate freely. Rotate the
10
