Panasonic AJ-D850A - page 68

Setup menus

– 68 –

USER menu <TIME CODE> (continued)

Item Setting

No.

Superimposed

No.

Superimposed

Description

display display

501 VITC 0000 10L

POS-2 0001 11L

0002 12L

0003 13L

0004 14L

0005 15L

0006 16L

0007 17L

0008 18L

0009 19L

0010 20L

502 VITC 0000 BLANK

BLANK 0001 THRU

503 TCG 0000 TC&UB

REGEN 0001 TC

0002 UB

504 REGEN 0000 AS&IN

MODE 0001 ASSEM

0002 INSRT

0003 SW

505 EXT TC 0000 LTC

SEL 0001 VITC

506 BINARY 0000 000

GP 0001 001

0002 010

0003 011

0004 100

0005 101

0006 110

0007 111

507 PHASE 0000 OFF

CORR 0001 ON

508 TCG CF 0000 OFF

FLAG 0001 ON

509 DF MODE 0000 DF

0001 NDF

The underline on the setting item denotes the initial setting.

This sets the position where the VITC signal is to be inserted.

(The same line as for VITC POS-1 in 500 cannot be selected.)

This selects whether to output the VITC data to the positions

selected by VITC POS-1 in 500 and VITC POS-2 in 501.

0: Data is not output.

1: Data is output.

This selects the signal to be regenerated when the time code

generator (TCG) in the REGEN mode.

0: Both the time code and user bit are regenerated.

1: Only the time code is regenerated.

2: Only the user bit is regenerated.

This selects whether the time code is to be regenerated during

automatic editing using the unit’s control panel.

0: Time code is regenerated with assemble or insert editing.

1: Time code is regenerated with assemble editing.

2: Time code is regenerated with insert editing.

3: Setting complies with REGEN/PRESET switch setting.

This selects the time code to be used when an external time

code is to be used.

0: The LTC of the TIME CODE IN connector is used.

1: The video signal VITC is used.

This sets the usage status of the user bit of the time code

generated by the TCG.

0: NOT SPECIFIED (character set not specified)

1: ISO CHARACTER (8 bits character set based on ISO646,

ISO2022)

2: UNASSIGNED 1 (undefined)

3: UNASSIGNED 2 (undefined)

4: UNASSIGNED 3 (undefined)

5: PAGE/LINE

6: UNASSIGNED 4 (undefined)

7: UNASSIGNED 5 (undefined)

This selects whether to control the phase correction of the

LTC generated by the TCG.

0: Phase correction control is not performed.

1: Phase correction control is performed.

This selects whether the CF flag of the TCG is to ON.

0: CF flag is OFF.

1: CF flag is ON.

This selects the DF/NDF mode for CTL and TCG.

0: Drop frame mode.

1: Non-drop frame mode.

No. 509 is valid when the CONTROL is LOCAL or LOCAL

ENA of item 004 to “ENA”.

Contents

Main IMPORTANT WARNING: CAUTION: Contents General and Features Features Features Time codes Multi-function input/output interfaces 2-channel high-sound-quality digital audio Automatic editing functions Front panel <Front Panel Top Section> Page Page Page Page Page Page Page <Front Panel Bottom Section> Connector area q rt i !2 !3 !4 !5 !6 !7 !0 !1 Page <Connector area> Connections when one unit is used Set the CONTROL switch on the front panel to LOCAL. Page Connections with editing controller Connections for adjusting video output (encoder output) signals Tapes Switching on the power/inserting the cassette Before starting to operate the unit, check whether the equipment has been connected properly. 1 2 3 1 3 2 4 STOP/STAND BY mode 1 2 Recording 1 2 3 4 5 5-1 Page Jog/shuttle Jog mode 1 2 3 Page Preroll 1 Page Page Selecting the editing mode 1 2 3 1, 2 3 1, 32, 4 Checking the edit points 2 1, 3 1 The value of the entered edit point appears on the display. 2 3 3-1, 3-2 2 Preview 1 Normal preview is now performed. Automatic editing Executing automatic editing 1 Page Page Audio split editing Button This denotes audio split editing. Entering the edit points Deleting the edit points Audio split editing Displaying the audio split edit points Cueing up the tape to the edit points Duration display Page Page Page Fig. 1 Fig. 2 Audio cross channel editing Example: To record cross-faded audio signals onto CH2 Connections 1 2 3 <Note> Select the video as well if the video signals are also going to be edited. Page V blanking data recording/playback Additional line recording/playback function Teletext signal recording/playback function Video output (encoder output) signal adjustments 1 2 4 3 3-1 Setup (default settings) Changing the settings 2 3 4 2 3 Setting and releasing the lock mode. 2 3 4 5 Loading a user file 2 3 4 5 6 Page SYSTEM menu <SYSTEM> SYSTEM menu <SYSTEM> Page Page Page Page Page Page Page Page Page Page USER menu <TIME CODE> Page Page Page Page Page Page Page Page Page Page USER menu Time code/user bit Time code User bit Page Reproducing the time code/user bit 1 2 3 4 Superimpose screen Servo reference 1 2 3 4 Servo reference setting tables Audio V Fade Function Rack mounting 1 2 5 Condensation Installing the mechanism dust protector Video head cleaning Error messages DIAG menu Displaying the DIAG menu 1 2 Displaying the HOURS METER information Error messages Warning messages Table of AUTO OFF Error messages Counter display Description VTR operation (Restart condition) Monitor display Table of AUTO OFF Error messages Counter display Description VTR operation (Restart condition) Monitor display 1. Introduction 2. Hardware specifications External interface specifications 3. Software specifications Protocol 4. Error code table 5. Command table (1) Commands relating to operation control Page (2) Commands relating to inquiries Page Connector signals VIDEO IN VIDEO OUT AUDIO IN AUDIO OUT PARALLEL REMOTE (25P) RS-232C REMOTE (25-pin D-SUB crossover cable supported) ENCODER REMOTE (15P) Printed circuit board Specifications GENERAL (Video signals adjustment) AUDIO (Digital audio) (Cue track)