Setup Menus
TIME CODE
| Item |
| Setting |
| |
|
|
|
| Description of setting | |
No. | Superimposed | No. | Superimposed | ||
| |||||
display | display |
| |||
|
|
| |||
|
|
|
|
| |
|
|
|
|
| |
500 | VITC BLANK |
|
| For setting whether to output the VITC signal to the position set by menu | |
|
|
|
| item No.501 (VITC | |
|
| 0000 | BLANK | 0: The VITC signal is not output. | |
|
| 0001 | THRU | 1: The VITC signal is output. | |
|
|
|
| <Note> | |
|
|
|
| This setting is only effective for SD outputs (VIDEO output and SD SDI | |
|
|
|
| output). | |
|
|
|
|
| |
501 | VITC | 0000 | 10L | For setting the position where the VITC signal is to be inserted. | |
|
| : | : | <Notes> | |
|
| 0006 | 16L | O The same line as that set for menu item No.502 (VITC | |
|
| : | : | be set. | |
|
| 0010 | 20L | O This setting is only effective for SD outputs (VIDEO output and SD SDI | |
|
|
|
| output). | |
|
|
|
|
| |
502 | VITC | 0000 | 10L | For setting the position where the VITC signal is to be inserted. | |
|
| : | : | <Notes> | |
|
| 0008 | 18L | O The same line as that set for menu item No.501 (VITC | |
|
| : | : | be set. | |
|
| 0010 | 20L | O This setting is only effective for SD outputs (VIDEO output and SD SDI | |
|
|
|
| output). | |
|
|
|
|
| |
503 | REGEN |
|
| For setting the synchronization method of the internal time code generator. | |
|
| 0000 | REGEN | 0: The time code reader is synchronized to the time code which is read | |
|
|
|
| from the tape. | |
|
| 0001 | PRE | 1: The synchronization method can be preset by a front panel operation or | |
|
|
|
| using the remote controller. | |
|
|
|
|
| |
504 | RUN MODE |
|
| For setting the operation mode in which the internal time code generator | |
|
|
|
| advances the time code. | |
|
| 0000 | REC | 0: The generator advances only during recording. | |
|
| 0001 | FREE | 1: It advances while the power is on regardless of the operation mode. | |
|
|
|
|
| |
505 | TCG REGEN |
|
| For setting the signal to be regenerated when the TCG (time code | |
|
|
|
| generator) is in the regeneration mode. | |
|
| 0000 | TC&UB | 0: Both the time code and user’s bit are regenerated. | |
|
| 0001 | TC | 1: Only the time code is regenerated. | |
|
| 0002 | UB | 2: Only the user’s bit is regenerated. | |
|
|
|
|
| |
508 | BINARY GP |
|
| For setting the conditions under which the user’s bit in the time code | |
|
|
|
| generated by TCG is to be used. | |
|
| 0000 | 000 | 0: Not specified (character set is not specified). | |
|
| 0001 | 001 | 1: ISO characters | |
|
| 0002 | 010 | 2: Unassigned 1 (not defined) | |
|
| 0003 | 011 | 3: Unassigned 2 (not defined) | |
|
| 0004 | 100 | 4: Unassigned 3 (not defined) | |
|
| 0005 | 101 | 5: Page/line | |
|
| 0006 | 110 | 6: Unassigned 4 (not defined) | |
|
| 0007 | 111 | 7: Unassigned 5 (not defined) | |
|
|
|
|
| |
509 | PHASE CORR |
|
| For setting whether to control the phase compensation for the LTC output | |
|
|
|
| during playback. | |
|
| 0000 | OFF | 0: The phase compensation is not controlled. | |
|
| 0001 | ON | 1: The phase compensation is controlled. | |
|
|
|
|
|
The underlining denotes the factory mode.
30