ERROR LED display (continued)

No.

 

 

REMAIN

 

 

 

 

 

Status

 

 

Corrective Action

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After clearing the error display 1),

 

 

 

 

 

 

 

A

formatting error

has

try formatting the card again. If

14

R

 

 

 

R

 

occurred with the P2 card.

the error recurs, switch P2 cards

 

 

 

 

(Other than write-protection or

and try formatting again. If the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

pulling out a P2 card)

 

 

error persists even after this,

 

 

 

 

 

 

 

 

 

 

 

 

 

contact the place of purchase.

 

 

 

 

 

 

 

 

 

15

R

 

R

 

R

 

A [Quick format] error has

There may be a problem with the

 

 

 

occurred on the internal HDD.

 

 

 

 

 

 

 

 

 

 

 

 

 

internal HDD. Contact the place

 

 

 

 

 

 

 

An [All erase] error has

16

R

 

 

 

R

R

of purchase.

 

 

 

occurred on the internal HDD.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

There may be a problem with the

 

 

 

 

 

 

 

 

 

 

 

 

 

internal HDD. If it contains data

17

R

 

 

 

 

 

A S.M.A.R.T error has

you need, first clear the error

 

R

 

R

 

occurred on the internal HDD.

display 1), and then back up the

 

 

 

 

 

 

 

 

 

 

 

 

 

data on a different storage

 

 

 

 

 

 

 

 

 

 

 

 

 

media, and contact the place of

 

 

 

 

 

 

 

 

 

 

 

 

 

purchase.

 

 

 

 

 

 

 

 

 

18

R

 

 

 

 

 

Copying failed, after which the

After clearing the error display 1),

 

 

 

 

R

unit was turned ON and the

try copying the data again.

 

 

 

 

 

 

 

error occurred.

 

 

 

19

R

 

 

 

 

 

[Quick format] failed, after

 

 

 

 

 

R

which the unit was turned ON

Execute [Quick format] again.

 

 

 

 

 

 

 

and the error occurred.

 

 

 

 

 

 

 

 

 

 

 

 

20

R

 

 

 

 

 

[All erase] failed, after which

 

 

 

 

 

OR

the unit was turned ON and

Execute [All erase] again.

 

 

 

 

 

 

the error occurred.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

R

 

 

 

 

 

After

an

internal

error

 

R

R

 

R

R

occurred,

copying

 

and

 

 

 

 

 

 

 

 

formatting is not possible.

 

 

 

 

 

 

 

 

 

 

 

 

 

There may be a problem with the

22

R

R

R

 

R

R

An

error

occurred

during

 

updating.

 

 

 

unit. Contact the place of

 

 

 

 

 

 

 

 

purchase.

 

 

 

 

 

 

 

Corrections are not applied.

23

R

R

 

 

 

R

The unit’s internal settings

 

 

 

 

cannot be adjusted, so an

 

 

 

 

 

 

 

 

error occurs.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contact the place of purchase

 

 

 

 

 

 

 

 

 

 

 

 

 

and replace the lithium battery.

24

R

 

 

 

 

 

The internal lithium battery is

Once this error is displayed, it

 

OR

 

 

 

drained.

 

 

 

 

will continue to be displayed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when the unit is turned ON until

 

 

 

 

 

 

 

 

 

 

 

 

 

you replace the lithium battery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The sensor has detected impact

Turn the unit OFF and ON.

25

R

R

R

 

R

R

to the HDD while writing

After placing the unit on a stable

 

administrative data or an HDD

 

 

 

 

 

 

 

access error has occurred.

 

surface, copy the data.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26

R

 

 

 

 

 

An error has occurred in the

If the data is important, back it up

 

R

 

R

R

control

information

of

the

on a different recording media,

 

 

 

 

 

 

 

internal HDD.

 

 

and proceed with [Quick format].

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1) To clear the error display, press the [POWER] button and [CANCEL] button together.

ENGLISH

E-30