Manuals / Panasonic / Computer Equipment / Personal Computer

Panasonic CF-74ECBGDBM Setting the SD PCB, Heat Sink and FAN Motor, Fan Dust Sheet, Pipe Sheet

Models: CF-74ECBGDBM

1 50

Download 50 pages 31.89 Kb

Page 36

9.2.7.Setting the SD PCB, Heat Sink and FAN Motor

1.	Connect the SD FFC to the Connector (CN1401).
2.	Fix the SD PCB to the computer using the three
	Screws<N9>.
3.	Set the Heat Sink, Fan Duct and the four Heat Sink
	Springs.
4.	Fix the FAN Motor to the computer using the two	<N9>
	Screws<N5>.	<N9>
	Screws<N5>.
5.	Attach the Fan Tape 1 and 2 on the FAN Motor, and fix
	the Cable Holder on them.

Screws <N5>: DXSB2+6FNL

Screws <N9>: DFHE5025XA

SD PCB SD FFC

Cable Holder Fan Tape1

Fan Duct

Fan Tape2 <N5>

FAN Motor

CN1401

Heat Sink

Spring

Heat Sink

Heat Sink

Spring

QApplying Grease on the Heat Sink

1.Apply grease on two points of the Heat Sink.

2.Attach the Pipe Sheet on the Heat Pipe.

Match the end of the Pipe Sheet. (0 ~ -2mm)

Fan Dust Sheet

(Attach the Fan Duct Sheet to the back side.)

0~1mm

0~1mm

0~1mm

0~1mm

5~10mm

Pipe Sheet

Fold on the center line and attach it.

Grease is applied.

G751(10mmX10mmXt0.3)

Fan Dust Sheet

Heat Sink

Grease is applied.

G751(10mmX10mmXt0.3)

9-14

Image 36

Panasonic CF-74ECBGDBM manual Setting the SD PCB, Heat Sink and FAN Motor, Applying Grease on the Heat Sink, Fan Dust Sheet

Contents

CF-74ECBGDBM Page Laser Safety Information Page Page Contents Bluetooth*12 Version 2.0+EDR Jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW ×Model No High-Speed CD-RW 4X/10XMaximum resolution depends on the specifications Only for model with wireless LANOnly for model with Bluetooth Operation has been tested and confirmed using PanasonicNames and Functions of Parts Right side Block Diagram Page Troubleshooting Error Diagnosis by Checking Beep Signal Sound Table of errors classified by beep soundsDiagnosis Beep signal sound Error message Outline of PostStuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility PC-Diagnostic utility End method Content of the setup is returned to the setting of the userSelection of tested device Content of standard test Content of enhancing test Record area frequently accessed All record area is testedTest item Stanard Ty of breakdownContent of Standard Test Content of Extend Test Express Card ConnectorWiring between Super I/O Test ItemWiring Connection Diagram Battery Pack PreparationRemoving the HDD HDD UnitRemoving the Dimm Memory Card Removing the KeyboardRemoving the Speaker and the LED PCB Removing the Bottom Case Removing the Main PCBRemoving the PC Card Ejector and Lithium Battery Removing the FAN Motor and SD PCBRemoving the DC-IN PCB and I/O Removing the USB PCB Removing the Display unitRemoving the LCD Front Cabinet Removing the LCD and the InverterRemoving the Touch PAD and PAD PCB Removing the Finger PCBPreparation Setting the Finger PCB Setting the LCD Unit InverterPreparing and setting the Finger Sensor Base Arranging the W-LAN L and R Cable Attaching the LCD Damper C and LCD Damper DArranging the LCD/TS Cable Attaching the ClothArranging the TP Power Cable and Attaching the TP/LCD Sheet Setting the Inverter and Arranging the Inverter CableLCD Unit LCD Rear CabinetSetting the LCD Front Cabinet Setting the Display unitFixing of the LCD Front Cabinet Ensure all the 23 Hooks are securely setSetting the USB PCB Safety Working MP Slide SheetArranging the USB Cable USB Cable TapeSetting the SD PCB, Heat Sink and FAN Motor Applying Grease on the Heat SinkFan Dust Sheet Pipe SheetSetting the DC-IN PCB and I/O PCB Arranging the DC-IN CableFAN Cable Sheet DC-IN Cable ~3mm INV. CableSetting the PC Card Ejector and Lithium Battery Setting the Main PCBArranging the Lithium Battery Safety Working Lithium BatteryNo.1 LAN Cable No.8 TP Power Cable FAN Cable Connector CN28Arranging the FAN Cable FAN Motor Main PCB TapeSetting the Wireless Module and MDC Module Arranging the Modem CableGood example Bad exampleSetting the Bottom Case Setting the Handle AssySetting the Speaker and the LED PCB Soldering the Speaker Cable and Setting the Speaker RubberSpeaker Red LineSetting the Keyboard Center Cover Hooks KBD Angle L Keyboard KBD Angle RSetting the Dimm Memory Card and Dimm Cover Setting the HDDSet the DVD-ROM Driver Unit Set the HDD Pack Exploded View 10-2 10-3 Screw tightening torque10-4 K17-6 K17-7