Manuals / Panasonic / Computer Equipment / Personal Computer

Panasonic CF-74ECBGDBM manual Setting the Dimm Memory Card and Dimm Cover, Setting the HDD

Models: CF-74ECBGDBM

1 50

Download 50 pages 31.89 Kb

Page 44

9.2.16. Setting the DIMM Memory Card and DIMM Cover

1.	Set the DIMM Memory Card to the Main PCB.	<N1>
2.	Fix the DIMM Cover using the two Screws<N1>.	<N1>
		<N1>
Screws <N1>: XSB2+3FNL		DIMM Cover
Screws <N1>: XSB2+3FNL
		Hook

Hook

DIMM Memory Card

9.2.17. Setting the HDD

1.Attach the HDD Earth Plate and HDD Conductive Sheet.

2.Connect the HDD to the HDD FPC.

3.Attach the HDD Dumper.

4.Fix the six Hooks, and attach the HDD Case.

HDD Case Upper

Hook

Hook

Hook

Hook

HDD

HDD FPC

HDD Damper

HDD Conductive Sheet

HDD Earth Plate

HDD Case

9-22

Image 44

Panasonic CF-74ECBGDBM manual Setting the Dimm Memory Card and Dimm Cover, Setting the HDD

Contents

CF-74ECBGDBM Page Laser Safety Information Page Page Contents Bluetooth*12 Version 2.0+EDR Jack, 3.5 DIA, Impedance 32 Ω, Output Power 4 mW ×Model No High-Speed CD-RW 4X/10XMaximum resolution depends on the specifications Only for model with wireless LANOnly for model with Bluetooth Operation has been tested and confirmed using PanasonicNames and Functions of Parts Right side Block Diagram Page Troubleshooting Error Diagnosis by Checking Beep Signal Sound Table of errors classified by beep soundsDiagnosis Beep signal sound Error message Outline of PostStuck key 02D0 System cache error Cache disabled Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Content of standard test Content of enhancing test Record area frequently accessed All record area is testedTest item Stanard Ty of breakdownContent of Standard Test Content of Extend Test Express Card ConnectorWiring between Super I/O Test ItemWiring Connection Diagram Battery Pack PreparationRemoving the HDD HDD UnitRemoving the Speaker and the LED PCB Removing the Dimm Memory CardRemoving the Keyboard Removing the Bottom Case Removing the Main PCBRemoving the DC-IN PCB and I/O Removing the PC Card Ejector and Lithium BatteryRemoving the FAN Motor and SD PCB Removing the USB PCB Removing the Display unitRemoving the LCD Front Cabinet Removing the LCD and the InverterPreparation Removing the Touch PAD and PAD PCBRemoving the Finger PCB Preparing and setting the Finger Sensor Base Setting the Finger PCBSetting the LCD Unit Inverter Arranging the W-LAN L and R Cable Attaching the LCD Damper C and LCD Damper DArranging the LCD/TS Cable Attaching the ClothArranging the TP Power Cable and Attaching the TP/LCD Sheet Setting the Inverter and Arranging the Inverter CableLCD Unit LCD Rear CabinetSetting the LCD Front Cabinet Setting the Display unitFixing of the LCD Front Cabinet Ensure all the 23 Hooks are securely setSetting the USB PCB Safety Working MP Slide SheetArranging the USB Cable USB Cable TapeSetting the SD PCB, Heat Sink and FAN Motor Applying Grease on the Heat SinkFan Dust Sheet Pipe SheetSetting the DC-IN PCB and I/O PCB Arranging the DC-IN CableFAN Cable Sheet DC-IN Cable ~3mm INV. CableSetting the PC Card Ejector and Lithium Battery Setting the Main PCBArranging the Lithium Battery Safety Working Lithium BatteryNo.1 LAN Cable No.8 TP Power Cable FAN Cable Connector CN28Arranging the FAN Cable FAN Motor Main PCB TapeSetting the Wireless Module and MDC Module Arranging the Modem CableGood example Bad exampleSetting the Bottom Case Setting the Handle AssySetting the Speaker and the LED PCB Soldering the Speaker Cable and Setting the Speaker RubberSpeaker Red LineSetting the Keyboard Center Cover Hooks KBD Angle L Keyboard KBD Angle RSetting the Dimm Memory Card and Dimm Cover Setting the HDDSet the DVD-ROM Driver Unit Set the HDD Pack Exploded View 10-2 10-3 Screw tightening torque10-4 K17-6 K17-7