Reference |
| DVD | VHS | ||
|
|
|
|
| |
Operation |
|
|
| Page | |
Cannot operate the TV. | ≥Change manufacturer code. Some TVs cannot be operated even if you change the code. |
| 18 | ||
| ≥Press [TV/VIDEO] to change the input mode to “TV”. |
| 25, 49 | ||
|
|
|
| ||
Cannot operate the DVD. | ≥Press [DVD] when operating DVD. |
| 10 | ||
Cannot operate the VHS. | ≥Press [VHS] when operating VHS. |
| 10 | ||
|
|
|
| ||
The remote control doesn’t | ≥The remote control code is wrong. Change to the correct code. |
| 18 | ||
work. | ≥The batteries are depleted. Replace them with new ones. |
| 10 | ||
| ≥Point the remote control at the remote control sensor on the main unit. |
| 10 | ||
| ≥Remove obstacles between the remote control and main unit. |
| – | ||
| ≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight |
| – | ||
| exposure. |
|
| ||
| ≥If you repeatedly insert discs or turn the unit on and off about 50 times or more, the recording | – | |||
| or editing of |
|
| ||
The unit is on but cannot be | ≥Some operations are prohibited by the disc. |
| – | ||
operated. | ≥The unit is warm (“U59” appears on the unit’s display). Wait until “U59” disappears. |
| – | ||
| ≥One of the unit’s safety devices may have been activated. |
| – | ||
| Reset the unit as follows: |
|
| ||
| (1) | Press [POWER Í/I] on the main unit to switch to standby. |
|
| |
|
| If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main unit for |
| ||
|
| about 10 seconds. The unit is forcibly switched to standby. |
|
| |
|
| Alternatively, disconnect the AC power supply cord, wait for about 1 minute, then |
|
| |
|
| reconnect it. |
|
| |
| (2) | Press [POWER Í/I] to turn the unit on. |
|
| |
|
|
|
| ||
Cannot eject a disc. | ≥The unit is recording. |
| – | ||
| ≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on the main unit | – | |||
| simultaneously for about 5 seconds. Remove the disc and consult the dealer. |
|
| ||
Startup is slow | ≥Make sure that “Quick Start” is set to “On”. |
| 41 | ||
| Even if “Quick Start” is set to “On”, startup is slow if the clock is not set, there was a power |
| |||
| failure or the AC plug has just been connected. |
|
| ||
| ≥A few dozen seconds after turning on the unit, you can play a disc or start recording to discs | – | |||
| other than |
|
| ||
| ≥Startup takes time for a few minutes after 4:00 a.m. due to system maintenance of this unit. | – | |||
|
|
| |||
Takes time to read | ≥It may take time to read a disc if it is being used for the first time in this unit or it has not been | – | |||
| used for a long time. |
|
| ||
Picture |
|
|
| Page | |
|
|
| |||
TV reception worsens after | ≥This can occur because the signals are being divided between the unit and other equipment. It | – | |||
connecting the unit. | can be solved by using a signal booster, available from |
|
| ||
|
|
| |||
The images from the unit do not | ≥Make sure that the TV is connected to the VIDEO OUT terminal, | 12, 14 | |||
appear on the TV. | COMPONENT VIDEO OUT terminals on the unit. |
|
| ||
Picture is distorted. | ≥Make sure that the TV’s input setting (e.g., VIDEO 1) is correct. |
| – | ||
≥The TV isn’t compatible with progressive signals. Press and hold [CANCEL] on the remote | – | ||||
| |||||
| control or press and hold [∫] and [“ DVD, DUBBING] at the same time on the main unit until |
| |||
| the picture is displayed correctly. The setting will change to interlace. |
|
| ||
| ≥Make sure that progressive output has not been selected when the connected TV is not |
| – | ||
| progressive compatible. Press and hold [CANCEL] until the picture displays correctly. The |
|
| ||
| setting will return 480i. |
|
| ||
|
|
|
|
|
62
VQT0R73