Panasonic EP1285 manual Setting Up The Unit

English

SETTING UP THE UNIT
WHERE TO USE THE UNIT
Keep at least 3.9 (10 cm) away from the wall.			• Avoid places where the unit will be exposed to direct sunlight
			for long periods of time or places where it will be exposed to
Approx. 76.8 (195 cm)			high temperatures, such as in front of a heater, etc., as this
	Approx. 11.8		can cause discoloration or hardening of the leather.
Width approx.			• Placing a mat or cloth under the unit is recommended to
		(30 cm)
27.5 (70 cm)			prevent floor damage. The size of the mat should be sufficient
Approx. 13.8			[at least 47.2 in. × 27.5 in. (120 cm × 70 cm)] to cover the
(35 cm)

3 HOW TO MOVE THE UNIT

Using the wheels to move the unit

•Grasp the legrest to move the unit when using the wheels.

•It is easier to move the unit with the massage heads

retracted and the backrest in the upright position.

*Place a mat or cloth on the floor and move the unit slowly to prevent floor damage.

Move it slowly

Lifting the Unit

• Move the unit by having one person hold the legrest and another person use the handles on the back.

*Please hold the handles and legrest securely to avoid dropping the unit as it may damage your floor.

English

areas where the unit touches and where the legrest could

touch the floor.

• Set the unit near the outlet.

See Warning No. 11 and 12 on page 1.

Mat

Area where legrest	Area where unit
could touch the floor	touches the floor

Legrest

Place your fingers inside the handle

Wheels

4 INSTALL THE ARMRESTS ON THE UNIT

1 UNPACK THE UNIT AND RAISE THE BACKREST

CAUTION

•When raising the backrest, be careful not to cause hands or feet to become caught between the backrest and the backrest latch or the backrest and the armrests.

Failure to follow this precaution may result in injury.

1	Remove the top of the shipping container.
	• When packed for shipping the backrest is folded forward.
2 Remove the packing and cushioning
	materials and take out all accessories.
Backrest latch 3	Raise the backrest.
	• Do not connect the power cord to an electrical outlet during setup.
	• Hold the backrest with both hands and lift in the direction of the
Check that there	arrow until it comes to a stop.
	• Be careful the power cord and controller are not caught in the
is nothing
around the unit.	backrest.

2 INSPECT CONTENTS OF SHIPPING CONTAINER

Left

Back

Front Zipper

Velcro

Convex

Round hole

FrontRear

Lift up

Secure with screws

Allen key

1 Install the armrests.

(Be careful to avoid damaging the coated fabric.)

1Unfasten the velcro.

2Unfasten the zipper of the armrest completely.

3Check the side (right or left) of the armrest. Check the direction (front or back) of the armrest as well. The illustration shows the left armrest. The right armrest

is stamped “Front”, “Right” and “Back”.

*The left armrest must be installed on the left hand side of the unit.

4Align the convex portion of the armrest with the round hole on the unit, and embed the armrest on the unit. Avoid catching the coated fabric between them.

If it is caught, pull it out without damaging the fabric.

2 Secure the armrests with attachment screws.

(Total of 4 positions for a single armrest)

Lift the coated fabric on the side of the armrest and insert the attachment screw onto the end of the Allen key, and then tighten.

(Tighten the screws in the 4 positions lightly at first, and then tighten all screws firmly.)

*If the screw does not enter into the hole, tighten the screw by pushing the armrest from the top.

Massage Lounger	Pillow	Back Cushion	Allen Key — 1	Lock Switch Key — 1
			Attachment Screws — 8

• The lock switch key has

Armrests — 2been inserted in the lock switch prior to leaving the factory.

3 Close the zipper at the bottom side of the armrests.

When closing the zipper, be careful not to twist the end of the zipper.

1Set the zipper.

2Fasten the zipper.

4 Put both ends of the zipper into the inside.

1Turn in the edge of the zipper.

2Fix the sliding tab of the zipper with the velcro.

7-8

2008/08/28 13:17:35