You can fully charge the shaver in 1 hour if the battery capacity monitor shows “low”.
The battery capacity monitor indi- cates the charge remaining in the battery in 3 levels (high/mid/low). The unit can be used once or twice more after “low” starts to blink. (Differs depending on the use situa- tion.)
A full charge will supply enough power for approx. 14 shaves (3 min- utes per shave for a normal beard). Before travelling, charge your shaver fully for 1 hour if you will not be taking the adaptor with you.
In case your shaver is without charge, you may quick charge it for 1 shave in about 5 minutes.
Using your shaver
Caution – The system outer foil is very thin and can be damaged if handled improperly. Before each use, always check the foil for dam- age. To avoid personal injury, do not use if the foil or other parts of the shaving head are damaged.
Disconnect the power cord from the shaver, and push the On/Off switch to turn the shaver on.
If you push and hold the On/Off switch for more than 2 seconds, it will activate the turbo mode for “sonic” vibration cleaning.
(see “Cleaning your shaver”) Caution:
Shaving with “sonic” vibration may damage your skin. Please turn it off and on again to deactivate the turbo mode.
8
8
Do not place fingers on the On/Off switch during use.
This may cause the shaver to stop during use or change it to the “sonic” vibration cleaning mode.
Hold the shaver at a right angle (90°) to your skin (see fig. 4). Start out shaving by applying gentle pressure to your face. Stretch your skin with your free hand and move the shaver back and forth in the direction of your beard. You may gently increase the amount of pressure as your skin be- comes accustomed to this shaver. Applying excessive pressure does not provide a closer shave.
System outer foil (see fig. 5)
System outer foil has a slit blade (a) between 2 foils (b). They move up and down independently to follow the contours of your face.
The slit blade catches and cuts longer and lying hairs easily.
For wet shaving
Put a thin layer of shaving foam on your face which works as a lubricant. Shaving foam is the most suitable among many other shaving aids (gel, soap, cream, etc.). Do not put a thick layer of shaving foam as it may af- fect shaver’s performance. If the shaving head is clogged with foam, simply rinse it under running water.
Using the trimmer
(see fig. 6)
Slide the trimmer handle up to open the trimmer.
Place the trimmer at a right angle to your skin and move it downward to trim sideburns.
Cleaning your shaver
(see fig. 7)
Warning – To prevent electric shock or personal injury, discon- nect the power cord from the shaver before cleaning with water.
For cleanliness and convenience, we recommend that you clean your shaver with water and a liquid hand soap. Regular cleaning will keep your shaver in good condition while pre- venting odors or bacteria from devel- oping, and maintain the cutting per- formance.
With the system outer foil in place, apply some hand soap onto the outer foil.
Push and hold the On/Off switch for more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning.
At the same time, the lamps of the Battery capacity monitor illuminate randomly.
Pour some water over the outer foil. After about 20 seconds, it will be automatically turned off, or you can turn it off by pushing the On/Off switch.
Remove the system outer foil and push the On/Off switch more than 2 seconds to activate the turbo mode for “sonic” vibration cleaning and clean it with running water.
Wipe off any moisture from the shaver with a dry cloth and dry it with- out the system outer foil.
9
9
Replacing shaving head components
It is recommended that you replace the system outer foil at least once a year and the inner blade at least once every 2 years to maintain your shav- er’s cutting performance.
Replacing the system outer foil (see fig. 8)
Squeeze the system outer foil re- lease buttons and lift the system outer foil upward to remove it. To in- sert the new system outer foil, press down until it snaps into place.
Replacing the inner blades (see fig. 9)
Squeeze the system outer foil release buttons and lift the system outer foil upward to remove it. Remove the in- ner blade one at a time by grasping each firmly at both ends and pulling straight away from the shaver.
Do not touch the metal parts of inner blades.
To insert the new inner blade, hold the blade one at a time at both ends and press downward until each snaps into the shaver.
ATTENTION:
A
