Panasonic KX-TSC14B Setting the Voice Mail Tone

“

Voice Mail Service

36

Setting the Voice Mail Tone

If your voice mail service sends a voice mail tone after a new message

has ﬁnished recording, set to “ON”. “ ” icon will ﬂash on the display if a

message was recorded in your mailbox. You will hear a series of voice

mail tones then a dial tone after lifting the handset or pressing

(SP-PHONE/HEADSET). (Contact your service provider about your service.)

Set to “OFF” when:

—you do not subscribe to a voice mail service.

—your voice mail service does not send a voice mail tone, or

—the unit is connected to a PBX.

Your phone comes from the factory set to “ON”.

Make sure that the handset is on the cradle, the AC adaptor is

connected and the SP-PHONE/HEADSET indicator light is off.

1Press (FUNCTION/EXIT).

2Press (_) or (^) repeatedly until

“VOICE MAIL TONE?” is displayed.

3Press (ﬂ) OK/EDIT.

4Press (_) or (^) to select the desired

line, “LINE1” or “LINE2”.

5Press (ﬂ) OK/EDIT (NEXT key).

6Press (_) or (^) to select the desired

mode.

7Press (ﬂ) OK/EDIT (SAVE key).

≥A beep sounds and the setting is saved.

≥The display will return to step 2. To

program the other line, start from step 3.

To return to the standby mode, press

(FUNCTION/EXIT).

≥You can exit the programming mode any time by pressing (FUNCTION/EXIT).

11:50AM11

/

24

SAVE AUTO# ?

11:50AM11

/

24

VOICE MAIL TONE?

11:50AM11

/

24

LINE1

1

=NEXT

LINE 1

11:50AM11

/

24

LINE2

1

=NEXT

LINE 2

11:50AM11

/

24

ON

1

=SAVE

PQQX12879ZA-BM03 01.3.7 3:52 PM y[W 36

Contents

Main Before Initial Use Accessories Contents Preparation Basic Operation Advanced Operation Useful Information Location of Controls Display 0-000-01-06-35 1-111-444-7777 1-123-456-7890 Settings Connecting the Handset/AC Adaptor Connecting the Telephone Line Cord Connect the telephone line cord(s) to the unit as follows. To connect a two-line telephone jack To connect two single-line telephone jacks If you use the unit only as a single-line telephone Connecting a Communication Device Setting the LCD Contrast 1 2 5 LCD CONTRAST ? Selecting the Dialing Mode 2 4 SET DIAL MODE ? TONE Selecting the Line Mode 2 LINE2 LINE1 SET LINE MODE ? A Programming Summary of Preparations Time and Date Adjustment 1 2 3 4 6 5 SET CLOCK ? 7 8 using a 4-digit number. (Ex. To set Dec. 27, enter 1227.) SET CLOCK ? 10 9 7 RINGER VOLUME ? HIGH LOW Making Calls 1 2 4 3 the MIC (microphone). Making Calls To redial the last number dialed To adjust the handset volume (4 levels) or the speaker volume (12 levels) while talking To put a call on hold 1 2 3 Using the Other Line During a Conversation 1 2 3 Conference Call 1 2 3 Caller ID Service How caller information is displayed when a call is received To check the number of new calls The display shows the number of new calls in the standby mode. For example, if you have received 10 new calls, the display on the right will be shown. Using the Caller List 2 Viewing the Caller List 3 To check who has called, follow the steps below. press (_). To search from the oldest call, press Ex. When you search from the most recent call: Press (_) to enter the list. 0 NEW CALL JOHN WHITE To return to the previous caller, press (^). To exit the Caller List, press 3 Calling Back from the Caller List desired caller. Editing a Callers Phone Number 3 You can edit a phone number recorded in the Caller List. 4 desired caller. pattern. 3 4 ((0) to (9)). (Ex. (1) is pressed as a memory station number.) Erasing Caller List Information After checking the Caller List, you can erase some or all of the entries. JOHN WHITE 3 To erase all entries in the Caller List Make sure that the unit is in the standby mode. 1 CLEAR 3 4 5 ENTER PHONE NO. AUTO=SAVE SAVE IN AUTO 1 3 4 CLEAR AUTO 1 (Ex. (1) is pressed.) Dialing a Stored Number 1 2 3 Voice Mail Service Storing an Access Number in Your Voice Mail 2 MAILBOX# ? is displayed. 6 line, LINE1 or LINE2. 32 digits. Setting the Voice Mail Tone VOICE MAIL TONE? ON Listening to Voice Mail Message(s) 1 2 3 4 Special Features For Call Waiting Service Users Call Waiting Caller ID Feature FLASH Button Selecting the ash time 6 7 SET FLASH TIME ? Special Features Temporary Tone Dialing (For Rotary or Pulse Service Users) How to Use the PAUSE Button (For Analog PBX Line/Long Distance Service Users) Line Selection 2 AUTO LINE SELECTION ? Special Features Incoming Call Tone INCOMING TONE ? ON Using an Optional Headset Connecting an Optional Headset to the Unit Using an Optional Headset Making/Answering Calls 1 2 Page Before Requesting Help Problem Remedy Problem Remedy Important Safety Instructions SAVE THESE INSTRUCTIONS FCC and Other Information Page For product service When you ship the product