ªFocus
Auto Focus Adjustment
The Auto Focus System automatically moves forward and backward the focusing lens inside the Movie Camera to bring the subject into focus so that the subject can be seen clearly. However, the Auto Focus System does not function properly for the following subjects or under the following recording conditions.
Please use the Manual Focus Mode instead.
1)Recording a subject whose one end is located closer to the Movie Camera and the other end farther away from it
≥Because Auto Focus makes adjustments at the centre of an image, it may be impossible to focus on a subject that is located in both foreground and background.
2)Recording a subject behind dirty or dusty glass
≥Because the focus is on the dirty glass, the subject behind the glass will not be focused.
3)Recording a subject in dark surroundings
≥Because the light information that comes through the lens decreases considerably, the Movie Camera cannot focus correctly.
4)Recording a subject that is surrounded by objects with glossy surfaces or by highly reflective objects
≥Because the Movie Camera focuses on the objects with glossy surfaces or on highly reflective objects, the recording subject may become blurry.
5)Recording a fast-moving subject
≥Because the focus
6)Recording a subject with little contrast
≥Because the Movie Camera achieves focus based upon the vertical lines of an image, a subject with little contrast, such as a white wall, may become blurry.
ªWhite Balance Adjustment
Depending on the type of light source, the colours recorded by the Movie Camera may be affected. In some cases, images may be recorded with bluish or reddish hue. To minimize the effect of light on the subject’s colour, what is called White Balance Adjustment becomes necessary.
White Balance Adjustment
White Balance Adjustment recognizes the colour of light and makes adjustment so that the white colour will become pure white.
Automatic White Balance Adjustment
This Movie Camera stores settings that are optimal for several kinds of general light sources. The Movie Camera determines the hue of light that it receives through the Lens and White Balance Sensor (l6), thereby judging the recording condition, and selects the closest hue setting. This function is called Automatic White Balance Adjustment. However, since white balance settings for only several kinds of light sources are stored, the Auto White Balance Function does not operate properly when recording occurs under light that is out of the range of the setup values.
ªTime Code
Time Code signals are data that indicate time measured in hours, minutes, seconds, and frames (25 frames per second). If this data is included in a recording, an address is assigned to each image on the tape.
≥The Time Code is automatically recorded as a part of the
≥When a new (previously unrecorded) Cassette is inserted, the Time Code automatically starts from zero. If a recorded Cassette is inserted, the Time Code picks up from the point where the last scene was recorded. (In this case, when the Cassette is inserted, the zero display [0h00m00s00f] may appear, but the Time Code starts from the previous value.)
≥The Time Code cannot be reset to zero.
≥Unless the Time Code is continuously recorded from the beginning of a tape, accurate editing may not be possible. To ensure that the Time Code will be recorded with no breaks, we recommend the use of the Camera Search Function (l18) or the Blank Search Function (l27) before recording a new scene.
ªMemory Stop Function
The Memory Stop Function is useful for the following operations.
Rewinding or
1Set [DISPLAY SETUP] >> [C.DISPLAY] >> [MEMORY].
2Reset the Tape Counter to zero at the tape position from which you want to play it back later. (l8, 14)
3Start playback or recording.
4After playback or recording has finished: Press the [MODE] Button to set the Movie Camera to VCR Mode.
≥The [VCR] Lamp lights up.
5Rewind the tape.
≥The tape automatically stops approximately at the position where the counter was set to zero.
Stopping editing automatically during audio dubbing
1Set [DISPLAY SETUP] >> [C.DISPLAY] >> [MEMORY].
2Reset the Tape Counter to zero at the position where you want to stop editing.
3Play back the still picture where you want to start audio dubbing.
4Start audio dubbing. (l30)
≥Audio dubbing automatically stops at the position where the counter was set to zero.
50
