Panasonic PT-AE3000U manual Position menu, Clock Phase, DOT Clock, Aspect

POSITION menu

Remote control Control panel

See “Navigating through the MENU” on page 29. See “Main menu and sub-menu” on page 30.

H-POSITION

You can move the projected image horizontally for fine adjustment.

CLOCK PHASE

If you require further adjustment for the same reason as the DOT CLOCK adjustment, you can fine adjust the timing of the clock. Press I H to adjust. (Available with signals from COMPUTER IN/COMPONENT IN only)

NOTE:

•If the projecting signal’s dot clock frequency is higher than 150 MHz, the adjustment may not make a difference.

•Available signals from COMPONENT IN:

1 125 (1 080)/60i, 1 125 (1 080)/50i, 1 125 (1 080)/60p, 1 125 (1 080)/50p, 1 125 (1 080)/24p, 750 (720)/60p, 750 (720)/50p.

Move left	Move
	right

V-POSITION

You can move the projected image vertically for fine adjustment.

Move	Move up
down

DOT CLOCK

If you have interference patterns of the projected image, which is sometimes referred to as moire or noise, you can minimize it by pressing I H to adjust the clock frequency. (Available with signals from COMPUTER IN only)

NOTE:

•If the projecting signal’s dot clock frequency is higher than 150 MHz, the adjustment may not make a difference.

•DOT CLOCK needs to be adjusted before adjusting the

CLOCK PHASE.

ASPECT

You can switch the aspect ratio manually when needed.

Aspect ratio depend on signals

Press I H to cycle through the aspect ratio options. The cycle pattern depends on the connected signals.

	4:3 \ 16:9 \ s16:9 \ JUST \ ZOOM
	\ AUTO
VIDEO/	NTSC, NTSC 4.43, PAL-M,PAL60
	signals
S-VIDEO
	4:3 \ 16:9 \ s16:9 \ 14:9 \ ZOOM1
	\ ZOOM2 \ JUST
	PAL, PAL-N,SECAM signals
	4:3 \ 16:9
COMPUTER	VGA, SVGA, XGA, SXGA, MXGA signals
(RGB)	Not switchable with WIDE480/600/720/
	768/768-2/800/900 signals
	4:3 \ 16:9 \ s16:9 \ H - FIT \ V - FIT
	\ ZOOM
	1 125 (1 080)/50i, 1 125 (1 080)/60i,
	1 125 (1 080)/50p, 1 125 (1 080)/60p,
HDMI	1 125 (1 080)/24p, 750 (720)/50p and
	750 (720)/60p signals
	4:3 \ 16:9 \ s16:9 \ JUST \ ZOOM
	525i (480i), 625i (576i), 525p (480p) and
	625p (576p) signals

4:3 \ 16:9 \ s16:9 \ 14:9 \ ZOOM1

\ZOOM2 \ JUST

625i (576i), 625p (576p) signals

	AUTO \ 4:3 \ 16:9 \ s16:9 \ JUST
	\ ZOOM
COMPONENT 525i (480i), 525p (480p) signals
(YPBPR)	4:3 \ 16:9 \ s16:9 \ H - FIT \
	V - FIT \ ZOOM
	1 125	(1 080)/50i, 1 125 (1 080)/60i,
	1 125	(1 080)/50p, 1 125 (1 080)/60p,
	1 125	(1 080)/24p, 750 (720)/50p,
	750 (720)/60p signals

Settings

ENGLISH - 37