Panasonic SC-AK250 External unit continued, Connecting and playing a USB mass, Dansk, Preparation

External unit (continued)

Connecting and playing a USB mass

storage class device For Australia and N.Z. AK250

ESPAÑOL	The USB connectivity enables you to connect and play
	MP3 tracks from USB mass storage class. Typically, USB
	memory devices. (Bulk only transfer)

Preparation

Before connecting any USB mass storage device to the unit, ensure that the data stored therein has been backed up.

It is not recommended to use a USB extension cable. The USB device is not recognised by this unit.

Compatible devices

Devices which are defined as USB mass storage class:

•USB devices that support bulk only transfer.

•USB devices that support USB 2.0 full speed.

Supported format

Files must have the extension “.mp3” or “.MP3”.

Note:

• CBI (Control/Bulk/Interrupt) is not supported.

• A device using NTFS fi le system is not supported [Only FAT 16/32

(File Allocation Table 16/32) fi le system is supported].

• Depending on the sector size, some fi les may not work.

• This unit can access up to 255 albums (including blank folders)

and 2500 tracks.

• The maximum number of tracks in a folder are 999 tracks.

DANSK

USB enabled device (not included)

It is not recommended to use a USB extension cable. The device connected via the cable will not be recognised by this unit.

- +

• Only one memory card will be selected when connecting a

multiport USB card reader. Typically the fi rst memory card

inserted.

• Disconnect the USB card reader from the unit when you remove

the memory card. Failure to do so may cause malfunction to the

device.

• When you connect your digital audio player to the USB port,

it charges all the time except in standby mode or during tape

recording.

MUSIC PORT	Changing the main unit and
	remote control mode

The remote control and main unit are factory-set to “REMOTE 1” mode.

FRANÇAIS	1 Reduce the volume and connect the USB mass storage
		device.
	2 Press [6, USB] to start play.
	To		Action
	pause play		Press [6, USB].
		USB	Press again to resume play.
	stop play		Press [7, CLEAR].
			“RESUME” is displayed. The position is
			memorized.
			Press [6, USB] to resume.
			Press [7, CLEAR] again to clear the position.
	skip tracks		Press [4, / REW] or [¢, / FF].
- 4
LANG
	skip album		Press [ALBUM (	or	)] in the play mode.
			Press [ALBUM (	or	)] once and then
			the numeric buttons in the stop mode.
	For other operating functions, they are similar as those
	described in “Discs” (\ page 9 ~ 11).
			Recording from a USB mass
			storage class device
5	1 Press [4, / REW ] or [¢,				/ FF] to select the
-		desired track for recording.
LANG	2 Press [¶, REC] on the main unit to start recording.
RQTV0196
16

RQT8043

If your remote control affects other equipment during operation, you can switch to operate in “REMOTE 2” mode.

To switch to “REMOTE 2” mode

1	While pressing and holding [MUSIC PORT] on the main
	unit
	Press and hold [2] until “REMOTE 2” appears on
	the main unit display.
2	Press and hold [ENTER] and [2] for at least 2

seconds.

The main unit and remote control are now set to operate in “REMOTE 2” mode.

To return to “REMOTE 1” mode

Perform steps 1 and 2 above but use [1] instead of [2] for both steps. (“REMOTE 1” appears on the main unit during step 1.)

The remote control cannot work with the main unit if their modes are different.

“REMOTE 1” or “REMOTE 2” appears on the main unit display when you operate the remote control.∗

∗If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)

Press and hold [ENTER] and [1] on the remote control for at least 2 seconds.

If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)

Press and hold [ENTER] and [2] on the remote control for at least 2 seconds.

RQTV0196-B.indd 16 2/23/07 4:49:38 PM