External unit (continued)
Connecting and playing a USB mass
storage class device
ESPAÑOL | The USB connectivity enables you to connect and play |
| |
| MP3 tracks from USB mass storage class. Typically, USB |
| memory devices. (Bulk only transfer) |
| Preparation |
| Before connecting any USB mass storage device to the unit, |
| ensure that the data stored therein has been backed up. |
| It is not recommended to use a USB extension cable. The |
| USB device is not recognised by this unit. |
DANSK | USB enabled device |
| (not included) |
| It is not recommended |
| to use a USB extension |
| cable. The device |
| connected via the cable |
| will not be recognised by |
| this unit. |
1 Reduce the volume and connect the USB mass storage device.
2 Press [6, USB] to start play.
FRANÇAIS | To | Action |
|
|
pause play | Press [6, USB]. |
|
| |
| Press again to resume play. | |||
| USB | |||
|
|
|
| |
| stop play | Press [7, CLEAR]. |
|
|
|
| “RESUME” is displayed. The position is | ||
|
| memorized. |
|
|
|
| Press [6, USB] to resume. | ||
|
| Press [7, CLEAR] again to clear the position. | ||
| skip tracks | Press [4, / REW] or [¢, / FF]. | ||
- 4 |
|
|
|
|
LANG | skip album | Press [ALBUM ( | or | )] in the play mode. |
| Press [ALBUM ( | or | )] once and then | |
| the numeric buttons in the stop mode. | |||
|
|
|
|
For other operating functions, they are similar as those described in “Discs” (\ page 9 ~ 11).
|
|
|
|
|
|
| Recording from a USB mass | |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| storage class device | |
|
|
|
|
|
|
| ||
5 |
| 1 Press [4, / REW ] or [¢, / FF] to select the | ||||||
|
| desired track for recording. | ||||||
- | 2 | Press [¶, REC] on the main unit to start recording. | ||||||
LANG | ||||||||
|
|
|
|
|
|
| ||
RQTV0205 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |
16 |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
RQT8043
Compatible devices
Devices which are defined as USB mass storage class:
•USB devices that support bulk only transfer.
•USB devices that support USB 2.0 full speed.
Supported format
Files must have the extension “.mp3” or “.MP3”.
Note:
•CBI (Control/Bulk/Interrupt) is not supported.
•A device using NTFS fi le system is not supported [Only FAT 16/32 (File Allocation Table 16/32) fi le system is supported].
•Depending on the sector size, some fi les may not work.
•This unit can access up to 255 albums (including blank folders) and 2500 tracks.
•The maximum number of tracks in a folder are 999 tracks.
•Only one memory card will be selected when connecting a multiport USB card reader. Typically the fi rst memory card inserted.
•Disconnect the USB card reader from the unit when you remove the memory card. Failure to do so may cause malfunction to the device.
•When you connect your digital audio player to the USB port, it charges all the time except in standby mode or during tape recording.
MUSIC PORT | Changing the main unit and |
| remote control mode |
|
|
The remote control and main unit are
If your remote control affects other equipment during operation, you can switch to operate in “REMOTE 2” mode.
To switch to “REMOTE 2” mode
1 | While pressing and holding [MUSIC PORT] on the main |
| unit |
| Press and hold [2] until “REMOTE 2” appears on |
| the main unit display. |
2 | Press and hold [ENTER] and [2] for at least 2 |
seconds.
The main unit and remote control are now set to operate in “REMOTE 2” mode.
To return to “REMOTE 1” mode
Perform steps 1 and 2 above but use [1] instead of [2] for both steps. (“REMOTE 1” appears on the main unit during step 1.)
The remote control cannot work with the main unit if their modes are different.
“REMOTE 1” or “REMOTE 2” appears on the main unit display when you operate the remote control.∗
∗If “REMOTE 1” appears (The main unit is in “REMOTE 1” mode.)
Press and hold [ENTER] and [1] on the remote control for at least 2 seconds.
If “REMOTE 2” appears (The main unit is in “REMOTE 2” mode.)
Press and hold [ENTER] and [2] on the remote control for at least 2 seconds.
2/22/07 7:02:53 PM |