11
RQT8043
RQTX0169
LANG - 5
LANG - 5
LANG - 4
LANG - 4
FRANÇAIS
FRANÇAIS
DANSK
DANSK ENGLISH

Cassette tape – Play and record

The buttons described for “Cassette tape - Play and record” are
mainly for the main unit unless indicated otherwise.
Basic play
Basic play
You can use either DECK 1 or DECK 2 for tape playback.
Use normal position tapes.
High position and metal position tapes can be played, but the unit will
not be able to do full justice to the characteristics of these tapes.
1 Press [3, TAPE].
The unit turns on.
If a cassette was loaded, play starts automatically (One touch
play).
2 Press [0, OPEN] for DECK 1 or [0, OPEN] for DECK 2 and
insert the cassette.
Insert with the side to be played facing towards you and the
exposed tape facing down. Close the holder by hand.
3 Press [3, TAPE] to start play.
To Action
stop tape playback Press [7, STOP].
fast-forward and
rewind Press [4, / REW ] or [¢, / FF].
select between
loaded decks Press [DECK 1/2] (remote control :
[PLAY MODE]).
Note:
• Tape playback is momentarily interrupted if you open the other
deck.
• Tapes exceeding 100 minutes are thin and can break or get caught
in the mechanism.
• Tape slack can get caught up in the mechanism and should be
wound up before the tape is played.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly.

Recording

Recording

Selection of tapes for recording
Use normal position tapes.
High position and metal position tapes can be used, but this unit will
not be able to record or erase them correctly.
Preparation
Wind up the leader tape so recording can begin immediately.
1 Press [0, OPEN] for DECK 2 and insert the cassette to be
recorded.
Insert with the side to be recorded facing towards you and the
exposed tape facing down.
2 Select the source to be recorded.
Radio recording:
Tune in the station (\ page 12).
Disc recording:
1 Insert the disc(s) you want to record.
Press [6, CD] and then [7, STOP].
2 Prepare the desired disc recording mode.
To Action
record
programmed
tracks Perform steps 2 to 4 in “Program play”
(\ page 9).
Perform steps 3 to 6 in “Program play”
(\ page 9).
By remote control only
record
specifi c
discs/tracks
1) Press [DISC] and then [1] ~ [5] to select
the disc.
Ensure disc is stopped.
2) Press [PLAY MODE] to select the desired
mode (\ page 8).
3)
For 1-ALBUM mode and 1-TRACK mode:
Press [ALBUM ( or )] to select the
album.
For 1-TRACK mode:
Press [4, / REW] or [¢, / FF ] to
select the track.
Tape-to tape recording:
1 Press [3, TAPE] and then [7, STOP].
2 Press [0, OPEN] for DECK 1 and insert the cassette to
record.
3 Press [, REC] to start recording.

Other basic operations

To Action
stop recording Press [7, STOP].
record on the other
side of the tape Turn the cassette over and press [, REC].
erase a recorded
sound 1) Press [3, TAPE] and then [7, STOP].
2) Insert the recorded tape into DECK 2.
Ensure there is no tape in DECK 1.
3) Press [, REC].
Note:
• Changes to volume and sound adjustments do not affect recording.
• You can only use DECK 2 for tape recording.
• You cannot open DECK 1 while recording.
• You cannot fast-forward or rewind one deck while recording with the
other.

Erasure prevention

The illustration shows how to remove the tabs to prevent recording.
To record on the tape again, cover as shown.
Side A
Tab for side ATab for side B
To re-record
Normal cassette
Adhesive tape
RQTX0169-P.indd 11RQTX0169-P.indd 11 7/18/08 9:24:56 AM7/18/08 9:24:56 AM