Panasonic SC-BTT750 warranty Display, TV / Device Connection, Audio

Audio

Dynamic Range Compression

You can listen at low volumes but still hear dialog clearly. (Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)

≥“Auto” is effective only when playing Dolby TrueHD.

Digital Audio Output

Press [OK] to show the following settings:

Dolby D/Dolby D +/Dolby TrueHD

DTS/DTS-HD

Select the audio signal to output.

≥Select “PCM”, when the connected equipment cannot decode the respective audio format.

≥Not making the proper settings may result in noise.

BD-Video Secondary Audio

Select whether to mix or not mix the primary audio and secondary audio (including the button click sound). (> 25)

≥If “Off” is selected, the unit outputs the primary audio only.

Display

Status Messages

Choose whether to show status messages automatically.

On-screen Language

Choose the language for menus and on-screen messages.

Screen Saver Function

This is to prevent burn-in on the screen.

≥When this is set to “On”:

If there is no operation for 5 minutes or more, DIRECT NAVIGATOR screen switches to START menu automatically.

≥While playing and pausing, etc., this function is not available.

≥While playing music (CD-DA or MP3), after about 5 minutes DIRECT NAVIGATOR screen switches to a blank screen with “Screen Saver” message.

FL Display

Changes the brightness of the unit’s display.

≥If “Auto” is selected, the display is dimmed but brightens when you perform some operations.

Digital Audio Input

Press [OK] to show the following settings:

PCM-FIX

Select the audio signal to input.

≥“On”: PCM is available.

≥“Off”: PCM and Dolby Digital are available. Select “On” if the sound is cut off intermittently.

Downmix

Select the downmix system to enjoy multi-channel or 2-channel sound.

≥Select “Surround encoded” to enjoy the surround sound.

≥There is no downmix effect on the bitstream audio signal.

≥The audio will be output in “Stereo” in the following cases:

–AVCHD playback

–Playback of secondary audio (including the button click sound).

7.1ch Audio Reformatting

Surround sound with 6.1ch or less is automatically expanded and played back at 7.1ch.

≥If “Off” is selected, sound is played over the original number of channels (Note that in the case of 6.1ch audio, playback

will be at 5.1ch.)

Audio reformatting is enabled in the following cases:

≥When you have selected “PCM” in “Digital Audio Output”.

≥When the audio is Dolby Digital, Dolby Digital Plus, Dolby TrueHD or LPCM.

High Clarity Sound

When connected to TV via the HDMI AV OUT terminal for outputting image, it produces clearer sound.

≥Set to “Enable” and then set “High Clarity Sound” on the Playback menu to “On”. (> 35)

Audio Delay

Mis-sync between the video and audio is corrected by delaying the audio output.

Speaker

Refer to page 40

FL Control (Vol 0)

≥If “On” is selected, the unit’s display will turn off when the volume is adjusted to “0”.

License

Information about the software used by this unit is displayed.

TV / Device Connection

3D Type

Select the format of the connected TV.

≥Change the settings for 3D on the TV also when “Checker board” or “Side by side” is selected.

TV Aspect

Set to match the type of television connected.

When connected to a 4:3 aspect television and playing 16:9 ratio image:

4:3	The sides are cut off so the
	picture fills the screen.
	When playing BD-Video,
	video is output as “4:3
	Letterbox”.

4:3 Letterbox Black bands appear at the top and bottom of the picture.

When connected to a 16:9 widescreen television and playing 4:3 ratio image:

16:9	Video is displayed as a 4:3 ratio image in the
	center of the screen.

Advanced operations

VQT2W18

37