Network Easy Setting
1 Select “Wired” or “Wireless” and press [OK].
Network Easy Setting (Connection Check)
Select a connection mode.
Current setting | : Wired |
LAN cable connection:
Connect a LAN cable to the unit and select "Wired."
Wireless LAN connection:
Connect the Wireless LAN Adaptor
Wired
Wireless
OK
RETURN
If “Wireless LAN Adaptor is not connected.” is displayed, check that the Wireless LAN Adaptor is fully inserted. Alternatively, disconnect and reconnect it. If there is still no change in the display, consult your dealer.
2 Follow the
For wireless LAN connection:
If you are using a Wireless router (Access point) that supports WPS, you can easily perform the settings by selecting “WPS (PUSH button method)”.
Otherwise, perform the settings by selecting “Search for access point” or “Manual setting” in “Other methods”.
Access Point Connection Setting
Select a connection method to use with an access point of Wireless LAN.
Please refer to the operating instructions of the access point about connection methods.
WPS (PUSH button method)
| Other methods | |
OK | Search for access point | |
WPS (PIN code method) | ||
RETURN | ||
| Manual setting |
≥WPS
| When you experience | started | |
| problems with settings | ||
|
| ||
Access Point Connection Setting | |||
Getting | |||
| Failed to connect to the access point. | ||
Access Point Connection Setting |
|
A conflict with another device occurred.
Do you want to configure Access Point Connection
Setting again ?
YesNo
OK
Display | Check the following |
A conflict with another | ≥ Please wait a few moments, |
device occurred. | and then try again. |
≥Setting of the Wireless router (Access point) for
A time out error occurred. | MAC Address etc. |
≥[BTT750] The signal may be weak. Using the supplied USB extension cable, adjust the position of the Wireless LAN Adaptor. Do not use any other USB extension cables except the supplied one.
≥[BTT350] The signal may be weak. Using the USB extension cable supplied
An authentication error or a | with the Wireless LAN |
time out error occurred. | Adaptor, adjust the position |
| of the Wireless LAN |
| Adaptor. |
|
|
| ≥ The SSID (> 20) and the |
| ||||
|
|
| encryption key of the |
| ||||
|
|
| Wireless router (Access |
| ||||
|
|
| point). |
|
|
|
| |
|
|
| ≥ Please wait a few moments, |
| ||||
|
|
| and then try again. |
| ||||
|
|
|
|
|
|
|
|
|
|
|
| ≥ Connection of Wireless LAN |
| ||||
A device error occurred. | Adaptor |
|
|
|
| |||
If there is no improvement in |
| |||||||
|
|
| symptom, contact our |
| ||||
|
|
| Customer Service Center. |
| ||||
|
|
|
|
|
|
| ||
Network Easy Setting (Connection Check) |
| |||||||
Network Easy Setting (Connection Check) |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| Complete. |
|
|
|
|
|
|
|
| 1. LAN cable connection | : Fail |
|
|
|
|
|
|
| 2. IP address setting | : Fail |
|
|
|
|
|
|
| 3. Connection to gateway | : Fail |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LAN cable is not connected. |
|
|
|
|
|
|
|
| Please check the connection. |
|
|
|
|
|
|
|
| Select “Yes” and press [OK] to check network |
|
|
|
|
|
| |
| connection again. Select “No” and press [OK] |
|
|
|
|
|
| |
| to finish Network Easy Setting. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Yes | No |
|
|
|
|
|
|
| OK |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Display |
|
| Check the |
|
| |
|
|
|
| following |
|
| ||
|
|
|
|
|
|
| ||
1. LAN cable connection or | :Fail | ≥ Connection of |
|
| ||||
Connection to access point | the LAN |
|
| |||||
|
|
|
| |||||
2. IP address setting | :Fail | cables (> 16) |
| VQT2W18 | ||||
|
|
| ||||||
3. Connection to gateway | :Fail |
|
|
| 19 | |||
|
|
|
|
|
|
|
|
|