Options Adjustments
Options1/3
Weekly Command Timer
Onscreen display |
| On |
|
|
|
|
|
Initial INPUT |
| Off |
|
Initial VOL level | Off | 0 |
|
|
|
|
|
Maximum VOL level | Off | 0 |
|
INPUT lock |
| Off |
|
Button lock |
| Off |
|
Remocon User level |
| Off |
|
Advanced PIP |
| Off |
|
Item | Effect | Adjustments |
Press 
button to adjust the volume when the unit is turned on.
|
| Off | On |
Initial VOL |
| Off: | Sets normal volume. |
level | Off On | On: | Sets your preferred volume. |
|
| Notes: |
|
•When “Maximum VOL level” is “On”, the volume can only be adjusted between 0 and your maximum range.
•You can hear the changed volume regardless of your volume setting before opening the options menu if you adjust the volume when “Initial VOL level” is “On” and cursor is on the menu.
Press 
button to adjust the maximum volume.
|
|
| Off | On |
|
|
|
|
|
| Off: | Sets auto maximum volume. |
| ||
Maximum VOL |
|
| On: | Sets your preferred maximum volume. | |||
level | Off | On | Notes: |
|
|
|
|
|
|
| • If the “Maximum VOL level” is set lower than the “Initial VOL level”, the “Initial VOL level” automatically | ||||
|
|
| becomes the same as the “Maximum VOL level”. | ||||
|
|
| • The volume display can go up to 63 regardless of the settings. | ||||
|
|
| • You can hear the changed volume regardless of your volume setting before opening the options menu if you | ||||
|
|
| adjust the volume when “Maximum VOL level” is “On” and cursor is on the menu. | ||||
|
|
| Off | PC | INPUT1 | INPUT2 | INPUT3 |
|
|
| Locks the input switch operation. |
| |||
|
|
| Notes: |
|
|
|
|
|
|
| • Only the adjusted signal is displayed (see page 18). | ||||
INPUT lock |
|
| • Signal can be displayed when the Terminal board is installed. | ||||
|
| • Input switch can be used when this is set to “Off”. | |||||
|
|
| |||||
•In two screen display mode, if anything other than “Off” is set, the value will be fixed as the value input in the single screen display mode.
•When a dual input terminal board is attached, A or B is displayed depending on the selected input signal. (Ex. INPUT1A, INPUT1B)
| Off | MENU&ENTER | On |
|
|
|
|
| |||
| Off: All the buttons at the right side of the main unit can be used. |
|
| ||||||||
| MENU&ENTER: |
|
|
|
|
|
|
|
| ||
|
| Locks | MENU and | ENTER/ | buttons on right side of main unit. |
|
| ||||
Button lock | On: Locks all the button on bottom face of main unit. |
|
|
|
| ||||||
| Sets Button lock with the unit buttons in the following procedure. |
|
|
| |||||||
| Off: Press | + / | four times→Press | INPUT four times→Press | four times→Press | ENTER/ | |||||
| MENU&ENTER: Press | ENTER/ four times→Press + / four times→Press | INPUT four times→Press ENTER/ | ||||||||
| On: Press | four times→Press | ENTER/ four times→Press | + / | four times→Press | ENTER/ | |||||
| Off | User1 | User2 | User3 |
|
|
|
| |||
| Off: | You can use all of the buttons on the remote control. |
|
|
|
| |||||
Remocon | User1:You can only use | , | , , | , , | , | , | buttons on the remote control. | ||||
User level | User2:You can only use | , | , buttons on the remote control. |
|
|
| |||||
|
|
|
| ||||||||
User3:Locks all the buttons on remote control.
| Off: |
| Sets normal two screen display mode (see page 22). |
| On: |
| Sets Advanced PIP mode (see page 23). |
Advanced PIP Off On | Notes: |
| |
• When “INPUT lock” is “On”, you cannot use all the two screen display functions. | |||
| • | , | buttons are unavailable during Advanced PIP mode operation. |
45
