Press to select 2 ⋅ 2, 3 ⋅, NTSC, PAL, Secam

Press to select Ratio (2nd step).

Setup for MULTI DISPLAY

How to set the display location number for each Plasma Display

MULTI DISPLAY Setup
Press to select “2⋅ 2”, “3⋅ 3”.		On
MULTI DISPLAY Setup		On
Ratio	2	2
Location		A1

Press to select Location.

Press to select the required arrangement number. (A1-C3 : Refer to the following)

MULTI DISPLAY Setup
MULTI DISPLAY Setup		On
Ratio	2	2
Location		A1

Display Number locations for each arrangement

( 2 ⋅ 2 )

( 3 ⋅ 3 )

6 R

Press twice to exit from Setup.

Notes:

(1)For RGB/PC input signals, normal multi-display magnification is only available at the VGA, SVGA and XGA resolution.

(2)The multi-display capability is functional for the following component signals:

525 (480) / 60i · 60p, 625 (575) / 50i · 50p, 1125 (1080) / 60i · 50i · 24sF, 750 (720) / 60p · 50p, 1250 (1080) / 50i

(3)The multi-display capability is functional for the following composite signals:

NTSC, PAL, SECAM

Page 29

Image 29

Panasonic TH-42PWD6, TH-50PWD6 operating instructions Press to select 2 ⋅ 2, 3 ⋅, NTSC, PAL, Secam

Contents

High Definition Plasma Display Operating InstructionsEnglish Model No. TH-42PWD6 Table of Contents Trademark Credits Important Safety Notice When using the Plasma Display Safety PrecautionsSetup Electric shocks can result if this is not done Cleaning and maintenanceIf problems occur during use Remote Control Batteries AccessoriesAccessories Supply Speakers ConnectionsTerminals L Speakers Terminals R AC cord connection see AC cord fixing GND Ground Signal Name Signal Names for D-sub 15P ConnectorPC Input Terminals connection SDA HD/SYNC SCL Command Installing the ferrite core Large sizeSerial Terminals connection Communication parameters Basic Controls Off Power On/Off Power On/Off and input signal selectionConnecting the plug to the Wall Outlet AC cord connection Selecting the On-Screen Menu Language Select the input signalINPUT1 INPUT2 INPUT3 Englishus On-Screen Menu Displays Press to Setup Press to access each adjust screen From the unitTo setup Multidisplay screen Press to Set up Aspect Controls Helpful Hint N / Normalise Normalisation Adjusting Picture Pos./SizeAdjusting screen Normal Picture AdjustmentsDynamic Cinema AGC Advanced settings Mute Sound Adjustment Display the Operation Guide Digital ZoomSelect the area of the image to be enlarged Select the magnification required for the enlarged display Present Time Setup Present Time Setup / Set up TimerPress to exit from Present Time Setup Present Time Display the Set up Timer screen Press to select Set up Timer Start setting Mode selectionScreensaver For preventing after-images Reversal / Scroll selection Press to select Screensaver Setup of Screensaver TimeReduces screen after-image This function may be applicable to the non-picture area Side Panel Adjustment INPUT3/VIDEO3/COMPONENT3/RGB3/PC3/DVD3/CATV3/VCR3/STB3 Reduces power consumptionCustomizing the Input labels How to Setup Multi Display Setup for Multi Display Press to select 2 ⋅ 2, 3 ⋅ Component/RGB-in Select Setup for Input Signals3D Y/C Filter For Ntsc AV images RGB Cinema reality Colour system / Panasonic AutoIf the picture image becomes unstable PAL Secam Ntsc Sync Setting RGB sync signalFreq. kHz/V-Freq. Hz Displays the H Horizontal/V Vertical frequencies Plasma Display panel Symptoms Check Troubleshooting Mark Input signal can be displayed TH-42PWD6 TH-42PHD6 TH-50PHD6 Specifications Customer’s Record

Press to select “2⋅ 2”, “3⋅ 3”.

NTSC, PAL, SECAM