Options Adjustments

Item

 

 

 

 

Adjustments

 

 

 

 

Locks the input switch operation.

COMPONENT*2

HDMI

DVI

PC

NETWORK

 

Off

SLOT INPUT*1

VIDEO

 

*1

“SLOT INPUT” is displayed when an optional Terminal Board is installed.

 

 

 

 

 

When a Terminal Board with dual input terminals is installed, “SLOT INPUT A” and “SLOT INPUT B” are displayed.

Input lock

*2

“COMPONENT” may be displayed as “RGB” depending on the setting of “COMPONENT/RGB-IN SELECT”.

 

 

(see page 51)

 

 

 

 

 

 

 

Notes:

 

 

 

 

 

 

•Only the adjusted signal is displayed (see page 18).

•Input switch can be used when this is set to “Off”.

Off MENU&ENTER On

Off: All the buttons on main unit can be used.

MENU&ENTER: Locks and buttons on main unit.

 

 

 

 

MENU

 

ENTER/

 

 

 

 

 

Button lock

On: Locks all the button on main unit.

 

 

 

 

Sets Button lock with the unit buttons in the following procedure.

 

 

 

Off: Press

four times→Press

four times→Press

four times→Press

 

 

MENU&ENTER: Press

 

INPUT

 

 

 

ENTER/

 

 

four times→Press four times→Press

four times→Press

 

 

On: Press

 

ENTER/

 

 

four times→Press

INPUT

 

ENTER/

 

four times→Press

four times→Press

 

 

 

 

 

 

 

ENTER/

 

 

 

ENTER/

 

 

Off

User1

User2

User3

 

 

 

 

 

Off:

You can use all of the buttons on the remote control.

 

 

Remocon User level

User1:You can only use

,

, ,

,

buttons on the remote control.

 

User2:You can only use button on the remote control.

User3:Locks all the buttons on remote control.

Enable: Enables the “Off-timer function”.

Off-timer function Disable: Disables the “Off-timer function”.

Note: When “Disable” is set, the Off-timer is cancelled.

 

Normal

Standby

On

 

Sets the power mode of the unit for when the power recovers from failure or after plugging off and in again.

Initial Power Mode

Normal: Power returns in as the same state as before the power interruption.

Standby: Power returns in standby mode. (Power Indicator : red/orange)

 

 

On:

 

 

Power returns in power On. (Power Indicator : green)

 

Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.

 

Sets panel ID number when panel is used in “Remote ID” or “Serial ID”.

ID select

Set value range: 0 - 100

 

 

 

 

 

 

(Standard value: 0)

 

 

 

 

 

 

The setting of this menu is valid only when using ID remote control.

 

Off:

Disables ID remote control functions. You can use normal remote control operations.

Remote ID

On:

 

Enable ID remote control functions.

Note: To use the ID remote control function, it is necessary to set each ID number of remote control and

 

 

 

display unit. About the setting method, please refer to “ID Remote Control Function” (see page 48)

 

 

and “ID select” (above-mentioned).

 

Sets the panel ID Control.

 

 

 

 

 

Serial ID

Off:

Disables external control by the ID.

 

On:

 

Enables the external control by the ID.

 

Adjusts the image display size on screen.

 

Off:

 

Sets the normal image display size on screen.

 

On:

 

Sets the image display size approximately 95 % of the normal image display.

 

 

 

 

Off

 

 

On

Display size

Notes:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• This setting is valid only when the input signals are as follows;

 

 

NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (Video)

 

525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,

 

1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)

 

• This setting is invalid when digital zoom, Multi display or Portrait display is selected.

 

• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS./SIZE” can be adjusted.

 

• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.

56