Panasonic DMP-BD45, VQT2H86-1, DMP-BD655 When you experience problems with settings

When you experience problems with settings

Access Point Connection Setting

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection

Setting again ?

Yes	No
OK

	Display		Check the following
	A conflict with another		≥ Please wait a few moments,
	device occurred.		and then try again.
			≥ Setting of the Wireless
			router (Access point) for
	A time out error occurred.		MAC Address etc.
			≥ The signal may be weak.
			Using the USB extension
			cable included with the
			Wireless LAN Adaptor,
			adjust the position of the
			Wireless LAN Adaptor.
	An authentication error or a		≥ The SSID* and the
	time out error occurred.		encryption key of the
			Wireless router (Access
			point).
			≥ Please wait a few moments,
			and then try again.
			≥ Connection of Wireless LAN
			Adaptor
	A device error occurred.		If there is no improvement in
			symptom, contact our
			Customer Service Center.
Network Easy Setting (Connection Check)
Network Easy Setting (Connection Check)
	Complete.
	1. LAN cable connection	: Fail
	2. IP address setting	: Fail
	3. Connection to gateway	: Fail

LAN cable is not connected.

Please check the connection.

Select “Yes” and press [OK] to check network connection again. Select “No” and press [OK] to finish Network Easy Setting.

YesNo

OK

1.	LAN cable connection or	: Pass	≥ Connection
Connection to access point			and settings
2.	IP address setting	: Fail	of the hub
			and router
3.	Connection to gateway	: Fail	≥ Settings of
			“IP Address/
1.	LAN cable connection or	: Pass
			DNS
Connection to access point
			Settings”
2.	IP address setting	: Pass
			(> 28)
3.	Connection to gateway	: Fail

Network Easy Setting (Internet Connection Check)

Network Easy Setting (Internet Connection Check)			Settings
	Complete.
	- Connection to the Internet :	Fail(Error code: B019)
	Failed the connection test.		&
	Cannot find the server.(Error code: B019)
			Connections
	OK
	Please refer to the operating instructions for the cause
	of the error and the solution for it.
	Press [OK].
	Display	Check the following
	Cannot find the server.	≥ “Primary DNS” and “Secondary
	(Error code: B019)	DNS” settings of “IP Address/
		DNS Settings” (> 28)

	≥ The server may be busy or the
Failed to connect to	service may have been
	suspended. Please wait a few
the server.
	moments, and then try again.
(Error code: B020)
	≥ Settings of “Proxy Server
	Settings” (> 28) and the router

≥ Refer to the operating instructions of the hub or router.

≥ You can perform this setup anytime by selecting “Network Easy Setting” in the Setup menu. (> 28)

≥ You can redo these settings individually using “Network Settings”. (> 28) ≥ Do not use this device to connect to any wireless network for which you

do not have usage rights.

During automatic searches in a wireless network environment, wireless networks (SSID*) for which you do not have usage rights may be displayed; however, using these networks may be regarded as illegal access.

≥ After performing network settings on this unit, the settings (encryption level, etc.) of the Wireless router (Access point) might change. When you have trouble getting online on your PC, perform the network settings on your PC in accordance with the settings of Wireless router (Access point).

* An SSID (Service Set IDentification) is a name used by wireless LAN to identify a particular network. Transmission is possible if the SSID matches for both devices.

	Display		Check the
			following
1.	LAN cable connection or	: Fail	≥ Connection of
Connection to access point			the LAN
2.	IP address setting	: Fail	cables (> 10)
3.	Connection to gateway	: Fail

13

VQT2H86