ParaBody 425101 ARM to Rotate Freely, Followed ~n step, PEGSEATdownto desired height. Release

SECURELYassemble the WEIGHTsTACKSHAFTto the HEADPLATEas shown on drawing, using one (I) 3/2 X 1~ IN. BOLT,one (1) 3/8 IN. LOCKWASHER,and one (I) 3/8 IN. WASHER.

Snaptwo(2)W3~IGHTPLATEBUSHINGSeach,intofiReen(}5)WEICHTPLATESshown in (DETAIL B)(IF.

ASSEMBLINGA 200 LB. STACK AT THIS TIME, SNAP TWO (2) WEIGHT PLATE BUSHINGSEACH INTO THE RE.~tAININGFIVE (S) WEIGHTPLATES)

USINGEXTRE~TECAREslide all fifteen (or twenty) WEIGHTPLATESdown over the CUIDIERODSonto the WEIGHTSTACKCUSHIONSas shown on drawing. (MAKESURE THATTHE KEY HOLESOF THE WEIGHT PLATES ARE ALL FACING THE SAME WAY)

Slide t~e HEADPLATEASSEMBLYdown over the GUIDERODSonto the WEIGHTSTACKas shown on drawing.

Swing th~ GUIDERODSunder the TOPBOOMas shownon drawing, and hold in place with two (2) GUIDERODPINS.

¯Auach the-WEIGHTSTACK-LABELStothe ..W.EIGHTSTACK:asshown on.drawing. Also .insertthe WEIGHTSTACK SELECTORPIN into the first WEIGHTPLATTEof the WEIGHTSTACK.

II.SECURELYAssemble one (I) ~/8 IN. SPRINGPIN ASSEMBLYto the SPRINGPIN HOUSING,of the LEG CURL/~XTENSIONARMas shown in (DETAIL C). (Ill IMPORTANT!!! TIGHTENTHENUTOF THE SPRING PIN ASSEMBLYSECUREL@.

12.Attach eight (8) PAKAGLIDESTRIPSto the AD.IUSTABLEROLLERPADSLEEVEas shown in (DETAILD),

.usingthe. followingsteps:

¯Thoroughlyclean all surfaces wherethe PARAGLIDESTR/PSare robe attached.

~.Removethe PAKAGLIDESTRIPSfromthe paper backing and firmly apply themto all showasurfaces.

13.Removethe 2 IN. SQ. ENDCAPfrom the bottom of the LEGCURLEXTENSIONAR~,I, pull back the SPRINGPIN, and Insert the ADJUSTABLEROLLERPADSLEEVEas shownin (DETAILE). Release the SPKI'NG,PIN into one of the adjustmentholes, and reinsert the 2 IN. SQ,ENDCAP.

15.Assemble the two (2) ROLLERPADSto the LEGCURLEXTENSIONARMas shown on drawing using one (I) ROLLERPADSHAFT,two (2) PLASTICWASHERS,and two (2) 9/I 6 MUSHROOMCAPS. (MAKESURE THE ROLLER PAD SHAFT IS INSERTED THROUGHLARGE HOLE ON THE ADJUSTABLEROLLER PAD SLEEVE)

16.¯ AssembletheLEGCURI./EXTENSIONARMto theFRONTUPRIGHTusingthefollowings~eps:

¯". Insert twO(2) 1/2 IN. FLANGEBEARINGSto the FRONTUPRIGHTas shown n drawing..

¯Assemble the LEGCURL/EXTENSIONARMto the FRONTUPRIGHTas shoumon drawing, using one (I) I/2 X 3-I14 IN. BOLT,two (2) I/2 TN. 3k'ASHERS,and one (1) I}2 IN. LOWI-I~IGI-IT LOCKNUT.(TIGHTEN CONNECTIONENOUGHTO REMOVETHE PLAY, YET ALLOWINGTHE LEG CURL/EXTENSiON

ARM TO ROTATE FREELY)

¯* Attach one (1) 1-1/4 IN. SO..RUBBERBUMPERto the FRON'rUPRIGHTwhcr~ the LEGCURL/EXTENSION ARMmakes contact. (SEE DRAWING).

17.Pre-.assemblethePECSEAT,usingthefollowingstep's:

¯:SECURELY~assembleoneof.theBACK/SEAT.PADStothePEG.SEATasshownondrawing,usingtwo(2)318 3 IN.BOLTS,two(2)3/8I"NLOCK.WASHERS,andtwo(2)3/8IN.WASHERS.

Assembletwo(2)ROLLERPADSto thePEGSEATas shownon drawing,usingone(I)ROLLERPADSHAFT, andtwo(2)9/I6 MUSHROOMCAPS.

__I_3.......: .A.~.n.~c/~ht(8)PAP,.AGLIDESTR.IPStotheFRONTUPRIGHTasshownin(DETAILF),andusilngthedirections

	followed ~n step I2.	"
',	Pull back the SPRINGPIN on the FRONTUPRIGHTand insert	the PEGSEATdownto desired height. Release the
	SPRINGPINand allow it. to engageinto the adjustment.holes. Use the THUMBSCREW~o tighten the PEGSEATin
	place.