Paradyne 3163 Starting Front Panel Emulation

ACCULINK 3163 DSU/CSU

F-2 March 1999 3163-A2-GB20-10

5. An Information screen appears. Choose Continue

to continue the installation.

6. Type the letter of the destination drive, followed

by a colon (default is C:), then the appropriate

directory name (default is C:\FRONTPAN).

If the selected directory already exists, the

following message appears: The specified

directory already exists. Do you want to

overwrite the directory?

If the selected directory is new, the following

message appears: The specified directory does

not exist. Do you want to create the directory?

7. Select Yes. A confirmation screen appears. Select

Install to continue the installation.

8. A Setup Completed screen appears. Select

Continue. The Program Manager screen appears

with the Front Panel icon.

Starting Front PanelEmulation

If the DSU/CSU selected is not locally attached to the

PC, you must first dial to the remote DSU/CSU before

starting front panel emulation. The modem attached to the

PC must support AT commands for the Front Panel

Emulation software to successfully place the call.

"Procedure

To start front panel emulation:

1. From the PC, open Program Manager from

Windows.

2. Double click on the Front Panel icon that appears

after the Front Panel Emulation program is

installed on the PC. The Front Panel window

opens.

3. Double click on the Front Panel icon that appears

in the Front Panel window. The Front Panel

Emulation screen appears.

4. Enter the Com Port and Speed from the

drop-down selection list boxes.

The Com Port field needs to contain the actual

communications port name as recorded in the

Windows information file (INI).

The Speed field needs to contain one of the

following communications speeds: 1200, 2400,

4800, 9600, 14400, 19200, or 38400 and should

match the DSU/CSU’s COM port configuration.

5. Choose either a Local (for near-end DSU/CSU) or

Remote (for far-end DSU/CSU) destination.

6. If you chose a Local destination, click on the

Execute button. If you chose a Remote

destination, enter the telephone number of the

far-end DSU/CSU in the Phone Number field,

then click on the Dial button.

7. The front panel of the selected DSU/CSU appears

on the PC.

NOTE

When using Front Panel

Emulation, no LEDs are shown on

the PC’s screen; you must use

the Stat command procedure to

get LED information (see the

Displaying LED Conditions

section in Chapter 3,

Operation

).

Contents

Main ACCULINK 3163 DSU/CSU Warranty, Sales, Service, and Training Information Trademarks Document Feedback !Important Safety Instructions !Warnings Page Page Table of Contents Preface 1. Introduction 2. Installation 3. Operation 4. Monitoring and Testing Appendices Glossary Index Preface Document Summary Section Description Related Documents Reference Documents Introduction Features Alarm Message Capability Front Panel Emulation Integral Modem Asynchronous Terminal Interface Support Telnet Access Physical Description Model 3163 DSU/CSU Front Panel Model 3163 DSU/CSU Rear Panel Installation Application Examples NETWORK Figure 2-1. Point-to-Point Application Example FRACTIONAL NETWORK Figure 2-2. Fractional T1 Application Example Important Instructions Optional Power Sources Installing the +24 Vdc Power Supply Installing the Single 48 Vdc Power Supply Installing the Redundant 48 Vdc Power Supply Cabling Examples The DSU/CSU is supplied with an ac power module and a VF cable for the integral modem. Figure 2-6. Cabling Examples PSTN T1 Network Power-Up Self-Test Page Operation Using the Front Panel Front Panel Emulation LCD Keypad Test Jacks LEDs Table 3-1 System LEDs Table 3-2 Network Interface LEDs Table 3-3 Data Port LEDs Displaying Unit Identity xxxxxxx xxxx Setting Customer Identification Displaying LED Conditions Changing Configuration Displaying/Editing Configuration Options Saving Edit Changes Configuring the DSU/CSU for Telnet Access Selecting the Port Setting the IP Address Selecting the Link Layer Protocol Configuring DS0 Channels Displaying DS0 Channel Assignments Allocating Data Ports Block or ACAMI Assignment Method Individual Channel Assignment Method Clearing DS0 Channel Allocation Selecting the Timing Source Configuring for Network Timing Establishing Access Security on a Port Setting a Password Entering a Password to Gain Access Acquiring/Releasing the User Interface Acquiring the Active User Interface User I/F Releasing the Active User Interface Enabling/Disabling the Front Panel Using the Integral Modem Entering Numbers in the Phone Directories Page Initiating a Call for Front Panel Pass-Through Operation Configuration Options), Initiating a Call for PC or ASCII Terminal/Printer Operation Disconnecting the Modem Connection Resetting the DSU/CSU Download Operations User Interface Access Security Changing User Interface Access Security Page Monitoring and Testing Self-Test Health Device Health and Status Table 4-2 Health and Status Messages Message Description xxxxxxxx Performance Reports xx,xxx Page Table 4-3 Performance Registers Register Totals DescriptionInterval Description Alarms Troubleshooting Table 4-4 Troubleshooting Symptom SolutionsPossible Cause Test Jacks Test Commands Remote Loopback Tests Sending a Line Loopback Up or Down Sending a V.54/ANSI FT1 Activation/Deactivation Local Loopback Tests Starting a Line Loopback CSUDSU Starting a Payload Loopback Starting a Repeater Loopback Starting a Data Channel Loopback CSUDSU Starting a Data Terminal Loopback Aborting Loopbacks Test Patterns Sending Test Patterns Name Name and Dest Monitoring Test Patterns Name Aborting Test Patterns Send or Mon Lamp Test Starting a Lamp Test Aborting a Lamp Test Displaying DSU/CSU Test Status Page A Front Panel Menu Page B Technical Specifications The technical specifications for the DSU/CSUs are listed in Table B-1. Table B-1 Models 3163 DSU/CSU Technical Specifications Specifications Criteria Table B-1 Models 3163 DSU/CSU Technical Specifications Specifications Criteria C Configuration Options Network Interface Table C-1 Network Interface Configuration Options Table C-1 Network Interface Configuration Options Sync Data Port Configuration Table C-2 (1 of 3) Sync Data Port Configuration Options Table C-2 (2 of 3) Sync Data Port Configuration Options Page Cross Connect Table C-3 Sync Data Port Assignment Options OR Table C-3 Sync Data Port Assignment Options nn Channel Configuration Table C-4 Data Port Channel Configuration Options OR Table C-4 Data Port Channel Configuration Options General Configuration Options Table C-5 General Configuration Options User Interface (1 of 5) (2 of 5) (3 of 5) (4 of 5) (5 of 5) Alarm Configuration Options Table C-7 Alarm Configuration Options Table C-7 Alarm Configuration Options Management Configuration (1 of 3) (2 of 3) (3 of 3) Configuration Worksheets Channel Options Options Value (Default in Bold) General User Options Value (Default in Bold) Alarm General Mgmt D Pin Assignments T1 Network Interface Page MODEM Port Interface COM Port Interface Page EIA-530-A Port Interface Connector EIA-530-A-to-RS449 Adapter The EIA-530-A-to-RS449 adapter (Figure D-6) provides the RS449 interface shown in Table D-5. Figure D-6. EIA-530-A-to-RS449 Adapter Table D-5 RS449 Cable Interface Signal Circuit Mnemonic CCITT Number Direction Pin EIA-530-A-to-V.35 Adapter The EIA-530-A-to-V.35 adapter (Figure D-7) provides the V.35 interface shown in Table D-6. Figure D-7. EIA-530-A-to-V.35 Adapter Table D-6 V.35 Cable Interface Signal CCITT Number Direction Pin EIA-530-A-to-X.21 Adapter The EIA-530-A-to-X.21 adapter (Figure D-8) provides the X.21 interface shown in Table D-7. Figure D-8. EIA-530-A-to-X.21 Adapter Page Serial Crossover Cable Figure D-9. Serial Crossover Cable Power Connector Optional DC Power Cable E IP Network Addressing Scenarios Scenario 1 Scenario 2 Scenario 3 Scenario 4 Figure E-4. Local Carrier Connected to Remote Carriers an Alternative 135.19.6.1 . . . . 135.19.6.16 135.19.20.1 . . . . 135.19.20.16 135.19.1.1 . . . . 135.19.1.16 Scenario 5 F Front Panel Emulation Installing Front Panel Emulation Software Starting Front Panel Emulation Displaying LED Conditions Operation Asynchronous Terminal Interface Operation G Before Using the Asynchronous Terminal Interface Restoring ATI Access Initiating an ATI Session Ending an ATI Session Menu Organization Figure G-2. Menu Organization Figure G-2 shows the organization of the ATI menu tree. Using ATI Screens Setting Customer Identification Displaying LED Conditions Changing Configuration Displaying or Editing Configuration Options Page Saving Edit Changes Establishing Access Security on a Port Setting a Password Entering a Password to Gain Access Configuration Worksheets for the ATI Page Page Page Management and Communication: Communication Protocol Options Front Panel Equivalent Value (Default in Bold) Page H Equipment List Equipment Feature Number Page Glossary Page Page Page Page Page Page Page Index A B C D E F G I L M N O P Q R S T U V W X Y