Paradyne 8335, 8355, 8365, 8385 3-10

3. Configuration

3-10 February 2003 8335-A2-GB20-70

4. Save the changes as prompted.

For . . . Enter . . .

Rate Table Standard – Selects the standard rate table for use when

operating with standard endpoints.

Nx128 – Selects the Nx128 rate table for use when operating

with nonstandard endpoints (most are multiples of 128).

Behavior The training behavior (Default = Auto Baud):

Fixed – The line card will train only at the rate set in the Fixed

Speed field (Standard default = 784kbps; Nx128 default =

768 kbps).

Auto Baud – The line card will train up to the highest

operational rate less than or equal to the rate set in Auto Baud

Max Speed.

Fixed Speed The DSL line rate if Behavior is set to Fixed:

Available Standard rates are 144, 272, 400, 528, 784, 1168,

1552, or 2320 kbps (Default = 784kbps).

Available Nx128 rates are 144, 256, 384, 512, 768, 1024, or

1536 kbps (Default = 784 kbps).

Auto Baud Max

Speed

The maximum DSL line rate the card can train to if Behavior is

set to Auto Baud:

Available Standard rates are 144, 272, 400, 528, 784, 1168,

1552, or 2320 kbps (Default = 2320kbps).

Available Nx128 rates are 144, 256, 384, 512, 768, 1024, or

1536 kbps (Default = 1536kbps).

Auto Baud Target

Margin

A range of 0 to 15 dB. The upper limit for margin used by the

Autobaud algorithm during training. After training, if the margin

is greater than the target margin, the card will attempt to retrain

at a higher rate, if the DSL line conditions permit. This field only

appears if Autobaud is selected (Default = 9 dB).

Auto Baud

Minimum Margin

A range of 0 to 15 dB. The lower limit for margin used by the

Autobaud algorithm during training. After training, if the margin

is less than the minimum margin, the card will attempt to retrain

at a lower rate. This field only appears if Autobaud is selected

(Default = 5 dB).

Link Down Count A number from 0 to 900 (Default = 0 (disable).

If the number of DSL Link Down events exceeds the selected

number within a 15-minute period, an SNMP trap is sent. If

Link Down Count is set to Disable, no Link Down trap is ever

sent.

Link Up/Down Trap Enable or Disable to enable/disable link up/down traps

(Default = Enable).

Enable – Enables link up/down traps.

Disable – Disables link up/down traps.

Contents

Main Page Contents About This Guide 1 About the Hotwire ATM Line Cards 2 Menus and Screens ii 3 Configuration 4 Monitoring 5Diagnostics Page Page About This Guide Document Purpose and Intended Audience This version of the New Features for This Document Release Hotwire ATM Line Cards, Models 8335, 8355, 8365, and 8385, Users Guide Product-Related Documents Complete documentation for this product is available online at www.paradyne.com. Select . Section Description Document Number Document Title About the Hotwire ATM Line Cards Hotwire ATM Line Cards 1-2 Hotwire ATM Line Card Features DSL Features ATM Features Endpoint Support Features Partners Hotwire Connected Interoperability Program. 1-4 Network Configurations Figure 1-2. Router Endpoint Figure 1-1 shows the Hotwire ATM Line Card used to carry voice over DSL. SNMP Management Capabilities Management Information Base (MIB) Support SNMP Trap Support SNMP Traps Page Menus and Screens Menu and Screen Formats 2-2 Components of a Hotwire Screen Naming Conventions for Ports and Interfaces 2-4 General Navigation Keys Pop-Up Menu Navigation Keys Table 2-1. General Navigation Keys Keys Definition Table 2-2. Pop-Up Menu Navigation Keys Keys Definition User Login Screen (MCP) 2-6 Quick Card Select Screen Hotwire Management Communications Controller (MCC) Card, IP Conservative, Users Guide Page 2-8 Exiting from the System Manually Logging Out Automatically Logging Out Configuration Overview Saving and Restoring Configuration Options 3-2 Entering Card Information Configuration Card Card Info Page 3-4 Entering the Time and Date Setting Spectrum Management (Models 8355 and 8385) Page 3-6 Other Functions of the Card Menu Maintenance Procedures Configuration Card 3-8 Configuring the DSL Ports Configuration Physical Ports DSL Ports DSL Port Configuration Model8335 Page 3-10 DSL Port Configuration Model8355 Copy Model 8355 DSL Port Configurations 3-12 Page 3-14 Page 3-16 DSL Port Configuration Model8365 Page 3-18 DSL Port Configuration Model8385 3-20 Setting Spectrum Management (Models 8355 and 8385) Page 3-22 Page 3-24 Configuring the ATM Physical Layer (Models 8335, 8365, and 8385) Configuration Physical Ports ATM PHY La ye r Page 3-26 Configuring ATM Parameters Configuration ATM Swi tc h ATM Parameters Page 3-28 Configuring ATM Cross Connections Configuration ATM Swi tc h ATM Cross Connect Page 3-30 Page 3-32 Configuring ATM Traffic Profiles Configuration ATM Swi tc h ATM Traffic Prof Page 3-34 Page 3-36 3. Save the changes as prompted. Clearing Cross Connections Configuration ATM Swi tc h Clear X-Connects 3-38 Configuring Rate Shaping (Models 8335, 8365, 8385) Configuration ATM Swi tc h Rate Shaping Page Page NOTES: Page Page Page Monitoring What to Monitor Viewing Card Status and Information Table 4-1. Monitoring Card Options Hotwire Management Communications Controller (MCC) Card, IP Cons13.3((M)-9c-0. Re Viewing Physical Ports Status Page 4-6 Table 4-2. Monitoring Physical Ports (2 of 6) Table 4-2. Monitoring Physical Ports (3 of 6) 4-8 Table 4-2. Monitoring Physical Ports (4 of 6) Table 4-2. Monitoring Physical Ports (5 of 6) 4-10 Table 4-2. Monitoring Physical Ports (6 of 6) Monitoring ATM Activity Monitoring ATM Sw it ch 4-12 Table 4-3. Monitoring ATM Switch (2 of 7) Table 4-3. Monitoring ATM Switch (3 of 7) 4-14 Table 4-3. Monitoring ATM Switch (4 of 7) Configuration Configuration, Configuring ATM Traffic Profiles Table 4-3. Monitoring ATM Switch (5 of 7) Configuring ATM Traffic Profiles Configuration Configuration, 4-16 Table 4-3. Monitoring ATM Switch (6 of 7) Table 4-3. Monitoring ATM Switch (7 of 7) Monitoring SN Information Table 4-4. Monitoring SN Information 4-20 Front Panel LEDs Indicating . . . Diagnostics Self-Test Page Alarms Table 5-2. Monitoring Card Alarms (1 of 6) 5-6 Table 5-2. Monitoring Card Alarms (2 of 6) (Continued on next page) Table 5-2. Monitoring Card Alarms (3 of 6) (Continued) 5-8 Table 5-2. Monitoring Card Alarms (4 of 6) Table 5-2. Monitoring Card Alarms (5 of 6) (Continued on next page) 5-10 Table 5-2. Monitoring Card Alarms (6 of 6) (Continued) ATM Pin g Diagnostics ATM Pin g ATM P in g C onf ig 5-12 ATM Ping Summary Diagnostics ATM Pin g ATM Ping Summary 5-14 Table 5-4. Diagnostics ATM Ping Summary Loopback Test (Model 8385 Only) Diagnostics Line Loopback 5-16 Table 5-5. Diagnostics Loopback Test Page Maintenance Procedures 6-2 Clearing NVRAM Configuration Card NVRAM Clear Uploading and Downloading a Configuration Configuration Card NVRAM Cfg Loader 6-4 Uploading a Configuration Downloading a Configuration Configuration Loader Statistics Resetting the Card Configuration Card Card Reset Page Page Page A Menus Configuration Menu A-2 Monitoring Menu Applications Menu The Application branch is not used on this product. Diagnostics Menu Page B SNMP Traps Trap Managers Hotwire Management Communications Controller (MCC) Card, IP Conservative, Users Guide SNMP Traps B-2 Table B-1. SNMP Traps (2 of 6) Table B-1. SNMP Traps (3 of 6) B-4 Table B-1. SNMP Traps (4 of 6) Table B-1. SNMP Traps (5 of 6) B-6 C Connector Pin Assignments Model 8820 GranDSLAM Telco Connector Pinouts C-2 Model 8620 GranDSLAM Telco Connector Pinouts D Technical Specifications Table D-1. ATM Line Card Technical Specifications (1 of 2) Specifications Criteria* D-2 Table D-1. ATM Line Card Technical Specifications (2 of 2) Specifications Criteria* Index A B C IN-2 D E F G H K L M N O P Q R S T U V W