Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 4960 manual Additional information

Models: 4960

1 67

Page 37

SmartNode 4960 Getting Started Guide4 • Initial configuration

Step	Command	Purpose

8	RedBoot> go	Starts the application image that was downloaded to the vola-
		tile memory (RAM).

Note This type of download takes about 25 minutes since it uses a serial link at only 9600 bps.

Additional information

For detailed information about conﬁguring and operating guidance, set up procedures, and troubleshooting, refer to the SmartNode Series SmartWare Software Conﬁguration Guide on the CD-ROM.

Additional information

VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 600030

Page 37

Image 37

Patton electronic 4960 manual Additional information

Contents

T1/E1 PRI VoIP Router SmartNode 4960 SeriesGetting Started Guide Trademark Statement Warranty InformationCopyright 2005-2006, Patton Electronics Company. All rights reserved Important InformationSummary Table of Contents sales@voipon.co.uk Table of ContentsTel +44 01245 Fax +44 01245sales@voipon.co.uk Table of ContentsTel +44 01245 Fax +44 01245Specifications List of Figures List of Tables Audience About this guideStructure Safety when working with electricity PrecautionsGeneral observations Typographical conventions used in this documentGeneral conventions Commands and keywords are in boldface fontConvention Indicates the names of command buttons that execute an actionMeaning SmartNode 4960 Getting Started GuideChapter 1 General information Chapter contentsSmartNode 4960 overview Standard compliant VoIP in accordance with SIP or H.323 protocols SmartNode 4960 rear panel sales@voipon.co.uk Tel +44 01245 808195 Fax +44 01245RESET SmartNode 4960 Getting Started GuideWAN ETH 0/0 SmartNode 4960 Getting Started Guide SmartNode 4960 front panel1 General information SN4960/4EDescription Chapter contents Chapter 2 Applications overviewApplication-Edge intelligence of enterprise communication IntroductionHow it works Application-Multi-service ISDN Internet telephony IADSmartNode 4960 Getting Started Guide Application-Multi-service ISDN Internet telephony IAD2 Applications overview Chapter SmartNode installationChapter contents Create a network diagram see section “Network information” on page Planning the installationVerify power source reliability see section “Power source” on page Network DiagramPower source Installing the gateway routerInstalling cables Software toolsConnecting the 10/100/1000Base-T Ethernet LAN and WAN cables Connecting the PRIConnect the cables in the following order Do the following to connect the main power to the Model Connecting the power supplyChapter contents Initial conﬁgurationChapter Introduction 1. Connecting the SmartNode to your laptop PCsales@voipon.co.uk Tel +44 01245Login Factory-default IP settings2. Conﬁguring the desired IP address Changing the WAN IP addresssales@voipon.co.uk Tel +44 01245 3. Connecting the SmartNode to the networkFax +44 01245 4. Loading the conﬁguration optional Start Bootloader BootloaderStart-up with factory conﬁguration Load a new application image SmartWare via TFTPDownload it after starting up SmartWare with the following command Command Load a new application image SmartWare via the serial linkRedBoot load -r -v -m StepAdditional information Additional informationChapter contents Chapter 5 G.SHDSL Basic ConﬁgurationConﬁguring PPPoE Line SetupIntroduction Figure 9. Conﬁguring the G.SHDSL card for PPPoEConﬁguration Summary Using PVC channels in bridged Ethernet mode Setting up permanent virtual circuits PVCUsing PVC channels with PPPoE Diagnostics Troubleshooting DSL ConnectionsPPPoE access Link StateChapter contents Chapter 6 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsContact information Patton support headquarters in the USAReturns for credit Out-of-warranty serviceReturn for credit policy RMA numbersChapter contents Appendix A Compliance informationSafety ComplianceCompliance SafetyRadio and TV Interference FCC Part 68 ACTA StatementCE Declaration of Conformity Industry Canada NoticeIndustry Canada Notice Chapter contents Appendix B SpeciﬁcationsVoice connectivity Voice processing signalling dependentData connectivity Fax and modem support Voice signallingVoice routing-session router Power Consumption 16W Operating temperature 32-104F 0-40C IP servicesManagement SystemFactor G.SHDSL Daughter Card if applicableSpecs DSL ConnectionSmartNode Model Identiﬁcation of the SmartNode devices via SNMPSysObjectID Chapter contents Appendix C CablingIntroduction ConsoleNote See section “Console port” on page 61 for console port pin-outs Ethernet EthernetFigure 13. Connecting an E1 PRI port to an NT1 E1 PRITo prevent damage to the system, make certain you connect the PRI cable to the PRI port only and not to any other RJ-45 socketT1 PRI T1 PRIChapter contents Appendix D Port pin-outsIntroduction Console portEthernet Note N/C means no internal electrical connectionG.SHDSL port PRI portSignal SignalChapter contents Appendix E SmartNode 4960 factory conﬁgurationIntroduction The factory conﬁguration settings for SmartNode 4960 are as followsIntroduction Chapter contents Appendix F End user license agreementEnd User License Agreement 5. Warranty1. Deﬁnitions 2. Title7. Other licenses 6. Termination