Rear Panel

17

18

19

 

 

 

 

 

 

 

 

 

 

OF FIRE HAZARD, REPLACE WITH SAME TYPE 250 VOLT FUSE.

SPEAKER OUTPUTS

CAUTION

 

 

 

GND.

 

DANS LE BUT DE REDUIRE LES RISQUES D’INCENDIE OU DE DECHARGE

120W RMS/44V RMS 4 MIN.

 

 

 

 

 

 

 

 

 

FUSE

 

 

 

REMPLACER PAR UNFUSIBLE DE MEME TYPE ET DE 250 VOLTS.

SPEAKER JACKS PARALLELED

 

 

 

 

EFFECTS

PREAMP

 

 

 

 

 

 

0

 

4

8 16

 

E UF

 

 

 

 

R

S

 

 

 

 

 

 

 

FUSE

120V

 

 

 

 

 

 

A PRODUCT OF PEAVEY

60 Hz

 

 

 

 

 

 

ELECTRONICS CORP.

5A

 

 

 

 

BUILT UNDER U.S. PATENT NO. 5,197,102

 

400 WATTS

 

SEND RETURN

OUT

SWITCH

 

MERIDIAN, MS MADE IN U.S.A.

 

 

 

CAUTION

REFER ALL SERVICING TO PEAVEY AUTHORIZED SERVICE CENTER

ALL TUBES 12AX7A

2022

21

Fuse (17)

A 5 amp fuse is located within the cap of the fuseholder. It must be replaced with the same type and value in order to avoid damage to the equipment and to prevent voiding the warranty. If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair.

WARNING: The fuse should only be replaced when the power cord has been disconnected from its power source.

Line Cord (120 V units only) (18)

For your safety, we have incorporated a three-wire line (mains) cable with proper grounding facilities. It is not advisable to remove the ground pin under any circumstances. If it is necessary to use the 6505 without proper grounding facilities, suitable grounding adapters should be used. Greatly reduced shock hazard exists when the unit is operated with the proper grounded receptacles.

Ground Switch (19)

This three position, rocker-type switch should be operated in the center (zero) position for most applications. If hum or noise is noticed coming from the speaker enclosure(s) with the ground switch in the center position, place the ground switch to positive or negative (+ or -) to minimize hum. Should a hum/noise problem continue, consult your authorized Peavey Dealer, the Peavey factory or a qualified service technician.

NOTE: The ground switch is not functional on 220/240 volt models.

Effects Send/Effects Return (20, 21)

Signals are supplied to outboard effects or signal processing units by patching from the EFFECTS SEND

[20]output into the outboard unit(s) and back into the EFFECTS RETURN [21] input using shielded cable with 1/4" phono jacks. Only non-gain effects devices (chorus, reverb, delay, etc.) should be used in the effects loop. Remote (on/off) selection of outboard effects devices can be achieved using the 6505 footswitch.

Preamp Out (22)

This output can be used to send a preamped signal from the 6505 to a mixing console, etc., using shielded cable. Patching from the PREAMP OUT does not affect the normal operation of the amplifier.

10

Page 10
Image 10
Peavey 6505TM owner manual Fuse, Line Cord 120 V units only, Ground Switch, Effects Send/Effects Return 20, Preamp Out

6505TM specifications

The Peavey 6505TM is a revered amplifier head that has secured its place in the pantheon of high-performance guitar amplification. Primarily designed for heavy metal and rock guitarists, the 6505TM boasts a robust feature set and technology specifically tailored to deliver powerful, aggressive sounds that have made it a mainstay in studios and on stages worldwide.

One of the defining characteristics of the 6505TM is its two-channel design, allowing guitarists to switch between pristine clean tones and high-gain overdrive. The clean channel provides a sparkling, crystal-clear sound, perfect for chord strumming and clean leads. The lead channel, on the other hand, is where the 6505TM shines with its high-gain capabilities, offering exceptional sustain and aggression ideal for heavy riffs and solos. Both channels come equipped with independent EQ controls, giving users complete tonal control.

A key highlight of the 6505TM is its use of all-tube circuitry, featuring a combination of six 12AX7 preamp tubes and four 6L6 power tubes. This all-tube design plays a crucial role in producing warm, rich tones and adds significant dynamic range to the amplifier. The amp also includes Peavey's patented Resonance and Presence controls, allowing players to tailor the response and articulation of the amp to fit their specific playing style and musical genre.

Another notable feature is the built-in effects loop, which provides versatility for integrating external effects pedals or processors, further expanding the tonal possibilities. The amp also includes a footswitchable channel switching option, making it easy to transition between clean and high-gain sounds during live performances without interrupting the flow of the music.

The Peavey 6505TM is constructed with durable materials designed to withstand the rigors of touring and heavy gigging. The iconic aesthetic of the amplifier, with its steel chassis and rugged design, exudes reliability and professionalism.

In summary, the Peavey 6505TM is a powerful amplifier that offers high-quality tone and robust features for guitarists seeking exceptional performance. With its versatile channels, all-tube design, and integrated effects capabilities, the 6505TM remains a favorite among musicians pursuing intense soundscapes and dynamic tonal options.