Peavey PR 15 D manual Peavey PR15D, Specifications

Peavey PR®15D

SPECIFICATIONS

ENCLOSURE: Peavey PR 15D (domestic)

FREQUENCY RESPONSE: 47 Hz to 20 kHz

LOW FREQUENCY LIMIT (-3 DB POINT):

36 Hz

USEABLE LOW FREQUENCY LIMIT (-10 DB

POINT):

42 Hz

INTERNAL POWER AMPLIFIERS (@120 VAC LINE):

Woofer - 150 Watts @ less than 0.1% distortion

Tweeter - 70 Watts peak dynamic power 50 Watts @ less than 0.1% distortion.

NOMINAL SENSITIVITY (1W @1M, SWEPT SINE INPUT IN ANECHOIC ENVIRONMENT):

97 dB

MAXIMUM SOUND PRESSURE LEVEL: 120 dB music peak

NOMINAL RADIATION ANGLES: 90˚ horizontal by 40˚ vertical

TRANSDUCER COMPLEMENT:

15" heavy duty woofer and RX™14 1.4" titanium diaphragm compression driver tweeter

BOX TUNING FREQUENCY (FBOX):

55 Hz

ELECTROACOUSTIC CROSSOVER

FREQUENCY: 2,000 Hz

CROSSOVER TYPE:

Internal Electronic two-way crossover with CD horn EQ, level matching, bass boost and subsonic filtering.

CROSSOVER SLOPES:

18 dB/octave (third order) low pass,

18 dB/octave (third order) high pass, both with staggered poles and driver EQ. Unit has horn spatially aligned with woofer.

ELECTRONIC INPUT IMPEDANCE (NOMINAL): 10 k ohms unbalanced, 20 k ohms balanced line level, 2.4 k ohms balanced mic level.

INPUT CONNECTIONS:

One combo female XLR/ 1/4" phone jack providing balanced operation, with switch selectable mic or line level sensitivity. Also has two 1/4" phone jack line level unbalanced input and output.

ENCLOSURE MATERIALS AND FINISH: Injection-molded polypropylene of a nominal thickness of 1/4" with internal ribbing and bracing, and with textured finish. Molded material is black.

MOUNTING:

Subwoofer pole-mounting via molded- in mount, flying via Versamount™ 70 and four rubber feet for floor use.

DIMENSIONS:

28.56" (72.5 cm) tall by 21.31"

(54.1 cm) wide {11.50"/29.2 cm in rear} by 17.00" (43.2 cm) deep

OPTIONAL ACCESSORIES: Impulse® 200 Floor Monitor Kit (FG# 00370480)

NET WEIGHT: 37 lbs.

ADDITIONAL REMARKS:

Also available as a passively crossed- over unit, the Peavey PR 15.

ELECTRONICS AND AMPLIFIER SPECIFICATIONS:

ELECTRONIC INPUT IMPEDANCE (NOMINAL): Primary balanced input: 20 k ohms line level sensitivity selected, 2.4 k ohms mic level sensitivity selected, 10 k ohms unbalanced 1/4".

MIC SWITCH SENSITIVITY INCREASE: 30 dB

INFRASONIC FILTER PROTECTION: 36 dB/octave roll-off

Woofer servo that subtracts error so that the woofer cone follows the drive waveform precisely.

Constant Loudness (Fletcher-Muson) circuit for accenuating bass and treble at low listening volume levels.

NOMINAL AMPLIFIER FREQUENCY RESPONSE: +0, -1 dB from 10 Hz to 30 kHz

HUM AND NOISE:

Greater than 90 dB below rated power

DDT DYNAMIC RANGE:

Greater than 14 dB

THD AND IM:

Typically less than 0.1 %

DAMPING FACTOR:

Greater than 100 @ 1000 Hz, 8 ohms

POWER REQUIREMENTS OF PEAVEY PR™15D SYSTEM (DOMESTIC): Nominal 110 watts, 120 VAC, 60 Hz

23