Pelco C1566M-C, C1572M - page 64

C1566M-C (10/05) 63

CM9780-MXB

ELECTRICAL

Input Voltage 100-240 VAC, 50/60 Hz, autoranging

Power Consumption 60 watts maximum (fully populated)

Communication Full duplex RS-422 using an RJ-45 connector

VIDEO

Inputs Card slots support up to 512 inputs per bay

Outputs Two output card slots for supporting 32 outputs per bay

Video Input Level 0.5 to 2 Vp-p, RS-170 composite video

Impedance 75 ohms terminating (looping versions available)

Crosstalk–Adjacent

Channel -61 dB at 3.58 MHz

V-Synch External connector available on rear panel

Overall Frequency Response Flat to 8MHz

Differential Gain 0.51%

Differential Phase 0.38 degrees

Luminance Nonlinearity 0.20%

Signal to Noise Ratio -71dBrms

GENERAL

Operating Temperature 32° to 122°F (0° to 50°C), noncondensing

Dimensions

Matrix Bay 10.5 (H) x 19.0 (W) x 21.7 (D) inches (26.67 x 48.26 x 55.10 cm)

Mounting Bafﬂe 1.75 (H) x 19.00 (W) x 24.00 (D) inches (4.45 x 48.26 x 60.96 cm)

CM9700-VPP 1.07 (H) x 19.00 (W) x 6.00 (D) inches (2.72 x 48.26 x 15.24 cm)

CM9700-VPP-RK 13.96 (H) x 19.00 (W) x 14.12 (D) inches (35.46 x 48.26 x 35.86 cm)

Mounting Fits 19-inch EIA-standard rack (6 RUs)

Unit Weight 33 lb (14.99 kg)

52 lb (23.59 kg), fully populated

(Design and product speciﬁcations subject to change without notice.)

Contents

Main ADDENDUM Page Contents Page List of Illustrations List of Tables Description Matrix Bay Controller and CPU Components MODELS Network Interface Unit Keyboards Compatible Receivers Optional Components Installation UNPACKING CM9700-VPP-RK CM9700-VPP CM9780-MXB MOUNTING Page Page CM9700-VPP VIDEO INPUT/OUTPUT CONNECTIONS Opening the CM9780-MXB Front Cover Installation Tips INSTALLING VIDEO INPUT CARDS (CM9780-VCC) Remove a Video Card Insert or Replace a Video Card How to Turn On the Pelco V-Sync Signal INSTALLING MONITOR OUTPUT CARDS (CM9780-VMC) Remove a Monitor Card Insert or Replace a Monitor Card PERFORMING A BASIC LED CHECK INSTALLING REAR PANEL CARDS Remove a Rear Panel Video DFC Card (CM9780-DFC) Insert or Replace a Rear Panel Video DFC Card (CM9780-DFC) Insert or Replace a Rear Panel Monitor BNC Card (CM9780-RPM) Page LOOPING VIDEO VIDEO INPUT/OUTPUT CAPACITY Single Bay Multiple Bays, Single Node C1566M-C (10/05) 23 Figure 14. Sample Sideframing System Using CM9780-DFC Cards in the Output Bay (1952 Cameras Maximum) 24 C1566M-C (10/05) Figure 15. Sample Sideframing System Using CM9780-RPC Cards in the Output Bay (4098 Cameras Maximum) Page Networked System THE POWER SUPPLY MODULE (CM9700-MPS) INSTALL A BACKUP POWER SUPPLY REMOVE A BACKUP POWER SUPPLY HOW TO REPLACE THE FUSE IN A POWER SUPPLY MODULE HOW TO TURN OFF THE AUDIBLE POWER SUPPLY ALARM SYSTEM DEVICE CONNECTIONS Page RS-422 COM PORT (SERCOM) CONNECTIONS Page 34 C1566M-C (10/05) Figure 24. Sample CM9780-MXB to CM9700-CC1 Connection CM9700-CC1 NODE 5 CM9700-CC1 NODE 7 CM9700-CC1 NODE 6 Figure 25. Sample CM9780-MXB and CM9700-CC1 Connections in a Networked System CM9700-NW1 System Start-Up INITIALIZE THE CC1 VERIFY SYSTEM OPERATION INITIALIZE KEYBOARDS DISPLAY THE CM9780-MXB SOFTWARE VERSION LEVEL DISPLAY A BLUE RASTER SCREEN MONITOR COLOR ADJUSTMENT Programming Your System GETTING HELP USING CM9700-MGR Operation OPERATING YOUR SYSTEM 9780 Switch Monitors Select Cameras Control Receivers Appendix SYSTEM ARCHITECTURE HOW TO EXPAND YOUR SYSTEM INSTALLING ADDITIONAL MATRIX BAYS Sideframing Change the Termination Jumpers on a Rear Panel Video BNC Card Page Downframing Figure 35. Looping Downframed Video with CM9700-VPP Patch Panels C1566M-C (10/05) 45 Downframe Card Figure 37. DFC Cable HOW TO INSTALL OR REPLACE A CM9700-SER CARD IN THE CC1 Figure 40. How to Install a CM9700-SER Card W2 ADDRESS SELECT W1 IRQ SELECT VIDEO INPUT CARD (CM9780-VCC) DETAIL MONITOR OUTPUT CARD (CM9780-VMC) DETAIL Page NETWORKING CONNECTING SATELLITE DEVICES PROGRAMMING SATELLITE DEVICES MOUNTING THE CM9780-MXB IN AN OPEN RACK DOS ENVIRONMENT AND COMMAND REFERENCE THE BOOT PROCESS AUTOEXEC.BAT AND THE BOOT PROCESS Invoking the CM9700 Executable File Names and DOS DOS Commands The Path Statement Navigating the DOS Directory Tree Manipulating Files in the DOS Environment Using the Wild Card Character DOS REFERENCE Page Troubleshooting Problems with the CC1 The VCC Card CF LED Is Illuminated and the AUX LED Is Blinking Monitor Display Problems LED Indicators on the Power Supply Module Specications Page Regulatory Notices PRODUCT WARRANTY AND RETURN INFORMATION REVISION HISTORY