Manuals / Pelco / Household Appliance / Home Security System

Pelco dx8100 manual Installing The New Hdds, Creating The Logical Drive

Models: dx8100

1 40

Download 40 pages 63.45 Kb

Page 29

INSTALLING THE NEW HDDS

a.Verify that the active Logical Drive is selected, and then press Enter.

b.Choose “Delete logical drive,” and then press Enter.

Figure 34. Delete Logical Drive

c. Select Yes on the shortcut menu, and then press Enter.

13.On the keyboard, press Esc twice to return to the Main Menu.

INSTALLING THE NEW HDDS

NOTE: You do not have to shut down the DX8100HDDI to install the new hard drives.

14.Install the new HDDs in the DX8100HDDI drive bays. For information about installing HDDs, refer to Installing the DX8100HDDI Drive Trays on page 15.

15.Verify that the DX8100HDDI status LEDs are flashing green and blue, indicating the drives are ready to be configured.

CREATING THE LOGICAL DRIVE

16.To access the Setup mode from the DX8100HDDI front panel:

a.If the IP address is still displayed in the LCD, press ESC five times.

b.Press and hold ENT for two seconds.

17.Press ENT to enter the Quick Logical Drive Install menu.

18.Press the down arrow to select RAID5.

PWR

BUSY

MUTE

ATTEN

ESC ENT

Figure 35. Quick Logical Drive Install

C3648M (7/08)

29

Image 29

Pelco dx8100 manual Installing The New Hdds, Creating The Logical Drive

Contents

DX8100 Series Digital Video Recorder C3648M 7/08I N S T A L L A T I O N SCSI Card and External Video StorageList of Tables ContentsImportant Safety Instructions Other DX8100 Optional AccessoriesC3648M 7/08 List of IllustrationsC3648M 7/08 RADIO AND TELEVISION INTERFERENCE Important Safety InstructionsRegulatory Notices Introduction ABOUT THE EXTERNAL STORAGE UPGRADEDX8100HDDI EXTERNAL VIDEO STORAGE Parts List and ToolsDX8100-ISCI SCSI CARD OTHER DX8100 OPTIONAL ACCESSORIES PREPARING THE SCSI CARD FOR INSTALLATION DX8100-ISCI SCSI Card InstallationWARNINGS OPENING THE CHASSISUNDERSTANDING THE COMPONENT LAYOUT MOVING THE MAIN CAPTURE CARD INSTALLING THE SCSI CARD REASSEMBLING THE UNIT INSTALLING THE UNITS Installing a New DX8100 and DX8100HDDI SystemINSTALLING THE DX8100HDDI DRIVE TRAYS Once installed, refer to Installing the DX8100HDDI Drive Trays3. Install the drive trays TURNING ON THE DX8100HDDI AND THE DX8100 CONNECTING THE DX8100HDDI TO THE DX8100Upgrading the DX8100 with the DX8100HDDI HARDWARE INSTALLATIONCONFIGURING THE DX8100 9. When the Computer Management window appears, click Disk Management 2 Select “Convert to Basic Disk.” 2 Click New Partition Figure 20. Unallocated Dynamic Drives a. Configure any unallocated drivesb. Perform a quick format 1 Click Next four times 2 Select the “Perform a quick format” check boxUSING ONLY DX8100HDDI EXTERNAL STORAGE 15. Click Close to exit the Computer Management application Figure 26. Selecting the Recovery Option C3648M 7/08 23. Repeat step 22 until all partitions are set to AllocationDELETING THE RAID ARRAY Upgrading the DX8100HDDI HDD Storage CapacityBACKING UP RECORDED VIDEO DATA OPTIONAL Figure 30. Entering the Telnet IP Address 11. On the keyboard, press Esc twice to return to the Main Menu Figure 32. Unmapping Partitions12. Select “view and edit Logical drives,” and then press Enter Figure 33. Main MenuCREATING THE LOGICAL DRIVE INSTALLING THE NEW HDDSUNMAP THE LOGICAL DRIVE OBTAINING AN IP ADDRESSPARTITIONING THE LOGICAL DRIVE Figure 42. Partition Logical Drive c. A warning message appears. Select Yes, and then press Enter Figure 48. Main Menu MAPPING THE PARTITIONS40. Press Enter four times Figure 53. LUN Mapping FORMATTING THE DRIVESALLOCATING THE NEW DX8100HDDI DRIVES Design and product specifications subject to change without notice SpecificationsELECTRICAL MECHANICALWARRANTY PRODUCT WARRANTY AND RETURN INFORMATIONRETURNS REVISION HISTORYUSA & Canada Tel 800 Fax 800 International Tel +1 559 Fax +1 ISO9001Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA