English
13

These operations are accessible by remote control.

Some may also be accessible by control panel on the main unit.

Initialsetup
This section will guide you through the unit’s initial setting which
includes selecting a language for your on-screen menu, country, location
and AutoProgram, which automatically scans and memorizes viewable
channels. You can also set the network connection in this setting.
Before you begin:
Make sure the unit is connected to antenna or cable.
1 After making all the necessary connections, press to Turn On the
unit.
• It may take a few moments to Turn On the unit for the rst time.
• Initial setup menu appears automatically after the unit is Turned
On.
2 Use ▲▼ to select the on-screen language, country, location on the
right side of the TV screen, then press OK.
• You must set Home in location setting. Otherwise, Picture and
Sound settings you adjusted will not be memorized after the unit
goes into Standby mode.
3 Use ▲▼ to select the signal type.
• If the TV is connect to a cable box or satellite set-top box, select
the 2nd one and skip to step 5.
TosetupaTVsignalfromacableTV
walljackorastandardTVantenna.
Select
TosetupaTVsignalfromacableTV
boxorsatelliteTVreceiver.
Select
4 Use ▲▼ to select Antenna for TV channels or Cable for CATV
channels, then press OK.
Makesurethatyouhave
attachedyourantennaorcable
signalintothejackontheback
ofyourTVlabeled“ANTENNA.IN”.
NowselecteitherAntennaor
Cable,usingup/downkeyofthe
remotecontrol.Onceyouhave
madeyouselection,pressthe
OKbuttontoproceed.
Antenna
Cable
Skip
– When Antenna is selected, the TV detects antenna signals. It searches
for DTV and Analog TV channels available in your area.
– When Cable is selected, the TV detects signals supplied by cable. It
searches for DTV, Analog TV and Cable channels available in your
area.
• Autoprogram will begin.
Systemsearching.Pleasewait...
Digitalchannelsfound: 0
Analogchannelsfound: 0
Autoprogrammingmaytakemorethan20minutesto
complete.DigitalchannelswilltakelongerthanAnalog
tofindandprogram.Pleasewaituntilyousee
theAutoProgrammingcompletemessage.
Stop
5 After the channel installation is completed, Network setup screen
will appear. Use ▲▼ to select Wireless or Wired, then press OK.
ThisTVcanbeconnectedto
yourhomenetwork.
Selectyourconnectiontype.
Wireless
Wired
Skip
Wireless If you have a router with WPS function, select
Wireless to connect to the Internet.
Wired If you connect with an Ethernet cable, select
Wired to connect to the Internet.
• If you select Wireless, use ▲▼ to select EasyConnect and
press OK.
6 Follow the on-screen instructions to complete the installation.
• When you select On in the selection screen of
Autosoftwareupdate. A message will appear if there is the
latest software on the network server.
7 Use ◄► to select Start,thenpress OK to begin Settingsassistant.
Settingsassistantwillallowyoutocustomizeyourpicturesettingstoyour
personalpreference.Youwillseeaseriesoftestpictureswhere
therightsideandleftsidediffer.Selectthesidethatismostpleasingto
youwiththeLeft/Rightbuttons.
Cancel Start
8 Press ◄ or ► 5 times to select the side of the pictures that is the
most pleasing to you, then press OK.
Whichsideofthepicturedoyouprefer?
Cancel Picture A Picture B
Continued on next page.